YSM40 Mainte_E - 第7页

v Safety instructions n Muzzle plate Usetheseplatesasasafetymeasurefortheboardconvey orentranceandexitopenings.Eachplateismo vable,soadjust themountingpositiontomatchtheboardstobeproduced. M…

100%1 / 160
iv
Safety instructions
1.8 Keeping hands away from moving parts
Duringuseofthismachine,thecustomer’sequipmentandoperatingconditionsmightallowtheoperator’s
handstocomeintocontactwithmovingparts.
Usethefollowingsafetymeasureoptionstoavoidpossibledangerwhereopeningsorgapsarefoundonthe
machine.
n
Dummy feeder
Usedummyfeedersassafetymeasurestofillagapbetweentapefeeders.Installdummyfeedersonthefeederplatethe
samewayasnormalfeedersinordertopreventhandsfromentering.
Prevention of hand entry
Dummy feeder
Dummy feeder (8mm-size)
Dummy feeder (Wide-size)
Clamp lever
91203-L0-20
c


machine has a structure that does not allow installing or removing a dummy feeder when the machine is in operation.

to attempt it.
n
One-stop cover (for machines (except for YSM40) with batch change carrier specs.)
Ifnotusingafeederexchangecarriageinthemachinethatistobeusedwithfeederexchangecarriages,installa
one-stopcoverinthepositionwhereafeederexchangecarriageistobeinstalled.
Prevention of hand entry
One-stop cover
One-stop cover
91204-L0-10
n
NOTE
One-stop covers cannot be installed or removed during operation. The machine must be in a stopped state because
the section where a feeder exchange carriage is to be installed will move up and down for the installation or removal
of the feeder exchange carriage.
v
Safety instructions
n
Muzzle plate
Usetheseplatesasasafetymeasurefortheboardconveyorentranceandexitopenings.Eachplateismovable,soadjust
themountingpositiontomatchtheboardstobeproduced.
Muzzle plate
Upper muzzle plate
Lower muzzle plate
Board conveyance plane
91205-L0-00
Upper clearance Lower clearance Remarks
YS100/YS88 8.0 to 38.5mm 1.0 to 31.0mm
From board conveyor plane
YS12, YS12P, YS12F, YS24,
YS24X, YSD
5.0 to 20.0mm 4.2 to 39.2mm
YSM40 0 to 44.0mm 0 to 39.0mm
Z:LEX (YSM20) 0 to 36.0mm 4 to 40.0mm
YC8 13.4 to 80.4mm 4.6 to 39.2mm
YSP 0 to 6.6mm 0 to 26.4mm
YSi-V 0 to 48.0mm 0 to 102mm
vi
Safety instructions
1.9 Handling solvents
Takethefollowingprecautionswhenhandlingcleaningsolventsduringsolderprintingorpreparation.
Hazards when handling solvents
1. Hazards to human health
Organicsolventsconstantlyvaporizeandcontaminatethesurroundingatmosphere.Inhalingorcomingincontactwith
organicsolventvapormaycauseseriousdamagetohumanhealth.
2. Flammability
Organicsolventsarehighlyflammablesubstancesandcaneasilycatchfireifhandledimproperly.
3. Adverse effects on machines
Somesolventtypeswilldamagethecleaningunit,electricalwiresheathandvariousunitsusedinthesolderpaste
printer.
To avoid hazards of solvents
1.Becarefulnottoinhaletoxicvaporsofsolventsforextendedperiods.
2.Donotusesolventsnearfireorflame.Keepsolventsawayfromflameorfire.
3.Useonlythespecifiedsolventinthecorrectmanner.Donotreuseanysolventrepeatedly,anddonotmixwithother
solventsorchemicals.
1.10 Handling the X-ray unit
SomeYSseriesinspectionequipmentmodelscontainanX-rayunit.Takethefollowingprecautionswhenusing
withanX-rayunit.
1. The X-ray output window of the X-ray source is made of very thin beryllium foil.
· Berylliumintheformofdustparticlescancauseacutetoxicityorchronictoxicity,andmayinducerespiratory
problemsifinhaled.
· Toensuresafety,theX-rayunitisdesignedsothattheX-raywindowcannotbetouched.However,shouldtheX-ray
outputwindowbebrokenforsomereason,immediatelyturnoffthepowerswitchanduseextremecarenottoinhale
thedustparticles.
· ChlorinegascancorrodetheberylliumwindowoftheX-raytube,causingpermanentdamagetotheX-raytube.Do
notusetheX-rayunitinenvironmentswherechlorinegasesaregenerated.Takespecialcarewhenhandlingsamples
suchasvinylchloridematerialswhichmaygeneratechlorinegases.
2. Lead is used in the covers of machines equipped with an X-ray unit.
Althoughleadissealedwithinthecoverssothattheleadportionscannotbedirectlytouched,usecautionsinceleadis
knownasheavymetalhavingharmfuleffects.
3. A safety key is provided for machines equipped with an X-ray unit.
Thesafetykeymustbemanagedbythesupervisorofthemachine.
4. Safety education about X-ray
AppropriatemeasuresaretakenforYAMAHA'sX-rayunitsothattheamountoftheX-rayleaktotheoutsideofthe
equipmentisverysmall.Therefore,whenusingthisequipmentinJapan,itisnotnecessarytosetcontrolledareasdefined
inArticle3oftheOrdinanceonPreventionofIonizingRadiationHazards.
Itisnotlegallyobligatedtoconductthesafetyeducation,butitisrecommendedtoconducttheeducationbythe
customer.
WhenoperatingthisequipmentoutsideJapan,thesafetyeducationisconductedasrequiredaccordingtotherelevant
country'slaws,regulations,andstandards.
TIP
When conducting the safety education in Japan, the contents stated in “Special Education Standard for Radiography
(Ordinance of the Ministry of Health, Labor and Welfare No. 50)” are recommended. However, the safety education
does not necessarily need to be these contents.