YSM40 Mainte_E - 第92页
3-24 3 Periodic maintenance items 6 Clean the linear scale. Use a dry cloth to dry-wipe the linear scale. If significant soiling exists, use an IP A to wipe it in one direction, then dry-wipe the ar ea. 53363-N5-00 c …
3-23
3
Periodic maintenance items
2.2.3 Cleaning and lubricating the X-axis guide (4-beam type)
1
Make the preparations for the cleaning and greasing work.
1. Take off all accessories susceptible to the magnetic fields, such as a wristwatch and/or magnetic ID
card.
e
2. Press the emergency stop button to put the machine in the emergency stop state.
3. Detach the batch change carriage.
4. Place a square cloth on the Y-axis linear area and the push-up plate.
2
Clean the guide.
1. Grasp the movement handle and move
the head unit to one end.
2. Using a paper cloth (clean room type)
which produces no lint, wipe the old
grease and soiling from the entire guide.
3. Move the head unit to the opposite side,
then clean the opposite-side guide.
53361-N5-00
3
Inject the grease.
Using a grease gun (bend type), inject the
prescribed grease (NSL) at the X-axis guide's
grease nipples (4 nipples).
53362-N5-00
n
NOTE
The head unit must be at the motor side when injecting
grease.
4
Remove excess grease.
1. Grasp the movement handle and move
the head unit to one end.
2. Wipe off the excess grease from the
guide end face.
3. Move the head unit to the opposite side,
then wipe the excess grease off the
opposite-side guide end face.
5
Check the grease condition.
1. Remove the square cloth.
2. Close the machine's cover, attach the
batch change carriage, then release the
"Emergency Stop" status.
e
3. Open the Warm-up screen, and perform
the warm-up operation for approximately
8 minutes. After the machine stops, wipe
off grease which has collected on the
guide end face.
c
Repeat Step 5 until grease accumulations no longer
present could cause the grease to spatter.
Cleaning the guide
Step 2
Cloth
Guide
Injecting the grease
Step 3
Front side
Bottom side, rear side
Grease gun
(bend type)
Grease gun
(bend type)
3-24
3
Periodic maintenance items
6
Clean the linear scale.
Use a dry cloth to dry-wipe the linear scale.
If significant soiling exists, use an IPA to wipe
it in one direction, then dry-wipe the area.
53363-N5-00
c
rubbing it with excessive force.
Cleaning the linear scale
Step 6
Cloth
Linear scale
Wipe in one direction
3-25
3
Periodic maintenance items
2.2.4 Cleaning and lubricating the X-axis guide (2-beam type)
1
Make the preparations for the cleaning and greasing work.
1. Take off all accessories susceptible to the magnetic fields, such as a wristwatch and/or magnetic ID
card.
e
2. Press the emergency stop button to put the machine in the emergency stop state.
3. Detach the batch change carriage.
4. Place a square cloth on the Y-axis linear area and the push-up plate.
2
Clean the guide.
1. Grasp the movement handle and move
the head unit to one end.
2. Using a paper cloth (clean room type)
which produces no lint, wipe the old
grease and soiling from the entire guide.
3. Move the head unit to the opposite side,
then clean the opposite-side guide.
53394-N5-00
3
Inject the grease.
1. Move the head unit to a position where
the lower guide grease nipple is seen as
shown in the figure at right.
2. Use a grease gun (standard type) to
pump the specified grease (NSL) into the
two grease nipples for the upper guide
and also into one grease nipple for the
lower guide.
53395-N5-00
4
Remove excess grease.
1. Grasp the movement handle and move
the head unit to one end.
2. Wipe off the excess grease from the
guide end face.
3. Move the head unit to the opposite side,
then wipe the excess grease off the
opposite-side guide end face.
5
Check the grease condition.
1. Remove the square cloth.
2. Close the machine's cover, attach the
batch change carriage, then release the
"Emergency Stop" status.
e
3. Open the Warm-up screen, and perform
the warm-up operation for approximately
8 minutes. After the machine stops, wipe
off grease which has collected on the
guide end face.
c
Repeat Step 5 until grease accumulations no longer
present could cause the grease to spatter.
Cleaning the guide
Step 2
Cloth
Guide
Injecting the grease
Step 3
Grease nipples for upper guide
Grease nipple for lower guide