4OM-996-007 - 第178页

Check Code Display Section A Display Section B 030401 Op er at i on Please input barcode data by manual input screen. Requirement 030402 Op er at i on Please check the operation in "pass" mode. Requirement 0304…

100%1 / 417
Check Code Display Section A Display Section B
030142 Operator’s Error [EMER STOP] switch and Open the F-axis safety door and Clean
the linear slide guide.
030143 Operator’s Error A pause conveyance function is effective. Please operate it after
setting up a function invalid.
030144 Operator’s Error Not found valid sequence. Attach a component to a nozzle.
030145 Operator’s Error Lock operation panel.
030146 Operator’s Error Please read of barcode label on the P.C.B.(front cnvr.)
030147 Operator’s Error Please read of barcode label on the P.C.B.(input cnvr.)
030148 Operator’s Error Please read of barcode label on the P.C.B.(input buffer cnvr.)
030149 Operator’s Error Please the [Jig Dtch (X/Y MVT)] menu select.
03014a Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode(barcode mode).
03014b Operator’s Error Lock front operation panel.
03014c Operator’s Error Lock back operation panel.
03014d Operator’s Error This operation is possible only front operation panel.
03014e Operator’s Error This operation is possible only back operation panel
.
03014f Operator’s Error Remove the P.C.B. at input machine cnvr.
030150 Operator’s Error Remove the P.C.B. at output machine cnvr.
030151 Operator’s Error [STOP] switch has been pressed.
030157 Operator’s Error Remove the P.C.B. at the output cnvr.
030158 Operator’s Error Remove P.C.B. on the X/Y table at Left side or Right side position.
030159 Operator’s Error Please make the priority alternate unit preparation complete.
(Only the priority unit use mode. )
030160 Operator’s Error Cannot start by the unit P.C.B. B.B.R. mode (communication/
barcode mode). Change pattern program single U-N pattern.
030201 Out Of Specified Rotate the rotary turret to designated angle.
Rotary Turret Angle
030301 Head Bypass Cancel bypass operation of selected head or do not use the head.
030302 Head Bypass The specified head is bypassed.
030303 Head Bypass The specified nozzle is bypassed.
030304 Specify the nozzle The specified nozzle type is not exist.
type
0509-002 2-6 AIM01ETRP
1.2 "CHECK" Windows
Check Code Display Section A Display Section B
030401 Operation Please input barcode data by manual input screen.
Requirement
030402 Operation Please check the operation in "pass" mode.
Requirement
030403 Operation X/Y chute P.C.B. detection is one side mode.
Requirement
030404 Operation Please exit P.E.C. manual adjustment mode.
Requirement (Click right and left button)
030405 Operation Please wait for a while.
Requirement (Now Machine is initializing.)
030406 Operation Nozzle level mismatch with component thickness (t). Collect
Requirement component and attach one again.
030407 Operation Recognition fail. Check data and component position.
Requirement
030408 Operation The current program changed. Please perform setup operation.
Requirement
030409 Operation Please check final mount step condition for eye adjustment.
Requirement This mount position was detected outside of the possible range.(PEC
position)
030410 Operation This teach point was detected outside of the possible range.
Requirement
030411 Operation This origin point was detected outside of the possible range.
Requirement (PEC position)
030412 Operation This destinate step was detected outside of the possible range.
Requirement (PEC position)
050101 No Current Select the current program.
050102 No Current Incorrect data found within internal current program. Please retry
program change.
050201 Setup Check Set up X/Y chute width.
050202 Setup Check Set up L conveyor width.
050203 Setup Check Set up R conveyor width.
050204 Setup Check Set up conveyor width.
050205 Setup Check Move the X/Y chute up.
050206 Setup Check Set up PCB support pins up/down.
050207 Setup Check Set up PCB locate lever.
050208 Setup Check Please input transfer stroke data.
050209 Setup Check Please input Zero Position.
05020a Setup Check Please input PCB locate lever size.
05020b Setup Check Set up X/Y chute width for Y-clamp action.
05020c Setup Check Please Transfer and Set P.C.B. on the X/Y table. (X/Y table on
P.C.B. is non clamp condition.)
0509-002 2-7 AIM01ETRP
1.2 "CHECK" Windows
Check Code Display Section A Display Section B
05020d Setup Check The P.C.B.-Clamp was detected Vacuum Leak. Please check the
P.C.B. -Clamp condition or Vacuum Leak Setting level.
05020e Setup Check "X-Clamp Pressure set value. ( "0" value is not active)."
050301 Recognition Data Please check recognition nozzle data and carry out data trans again.
Missing
050302 Recognition Data Please check comp recog lighting data and carry out data trans
Missing again.
050303 Recognition Data Please check recog camera mag data and carry out data trans
Missing again.
050304 Recognition Data Please check recog camera offset data and carry out data trans
Missing again.
050305 Recognition Data Please check recog camera gain level data and carry out data trans
Missing again.
050306 Recognition Data Please check recog nozzle gain level data and carry out data trans
Missing again.
050307 Recognition Data Please check comp recog data and carry out data trans again.
Missing
050308 Recognition Data Please check recog execution mode data and carry out data trans
Missing again.
070101 Front Safety Door Close the safety door and zero all device with the [ZERO] button.
070201 Rotary Wheel Pull on the rotary wheel handle.
070301 Front Area Sensor Remove foreign substance.
070401 Unavailable Data Input available feeder No. in current program.
070402 Unavailable Data Input available placement step in current program.
090101 Disengaged PCB Set P.C.B. on the X/Y table.
090201 Chute Lower Limit Move the X/Y chute down.
090301 Feeder Carriage Separate both feeder carriages and zero all devices with the [ZERO]
Collision button.
0509-002 2-8 AIM01ETRP
1.2 "CHECK" Windows