4OM-996-007 - 第308页

Error ID Item Description 430a02 Oil Cooler The oil cooler flowmeter alarm was detected. (Cause 1) The cooling oil filter in the driving section of the main body may be defective. (Remedy 1) Replace the oil filter with a…

100%1 / 417
Error ID Item Description
430701 Linear Measure Linear measure alarm signal was detected.
430702 Linear Measure Communication error in linear measure system.
430703 Linear Measure Upper limit of linear measure data was out of range.
430704 Linear Measure Lower limit of linear measure data was out of range.
430705 Linear Measure Linear measure dirty signal was detected.
430706 Linear Measure Linear measure SYNC signal has been lost.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
430707 Linear Measure The Linear Measure sensor has been detected Component
output error.Please check nozzle of error head.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Refer to "2.7 Component Backtrack Detection Function" in "Section 2" (Vol. 2)
for the remedial procedures.
430801 Cam-Positioner Cam-positioner alarm signal was detected.
(Cause 1) The cam positioner is abnormal.
(Remedy 1) Press the [RETURN] button to cancel the error display and contact our service
personnel for the remedy.
430901 Auto Recovery Cannot recover sequence.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
430a01 Oil Cooler Oil cooler alarm signal was detected.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0509-001 2-115-1 AIM01ETRP
Error ID Item Description
430a02 Oil Cooler The oil cooler flowmeter alarm was detected.
(Cause 1) The cooling oil filter in the driving section of the main body may be defective.
(Remedy 1) Replace the oil filter with a new one.
Refer to "1.4.12 Replacement of Oil Filter" for the replacement procedure.
430a03 Oil Cooler Oil cooler operation fails. See if pressure sensor works,
or breaker works, or power source incapable.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
430b01 Cooling FAN Cooling FAN alarm signal was detected.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
430c01 Pickup Position Feedback Feedback value out of range. Please check feeder.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
430d01 Missing Large Comp. Fdr. Crg. is paused to avoid clash with missing component.
(Cause 1)Self-Diagnostics Error Message
(Remedy 1) Check the air pressure and zero all axes. After that, re-start the operation.
When the machine cannot be set to its normal condition, consult our service per-
sonnel for the remedy.
430e01 Air Cylinder Low pressure.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Check the air pressure and zero all axes. After that, re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
3.3 Error IDs and Remedial Procedures
0509-001 2-115-2 AIM01ETRP
Error ID ltem Description
430f01 Component Pick-up miss Component Pick-up miss was detected. Please remove the
componet before the operation of the Feeder Unit.
(Cause 1) A component may be trapped (tilted vertically) between the tape feeding plane and
the suppressor of the tape feeder.
(Remedy 1) When the [RESET] button is pressed, the following "adsorption err operation"
window opens.
Follow the instructions in this window and the operational procedure below.
Fig. 4B21-1
(1) Select the [F1], the [F2], the [F3], or the [F4] button corresponding to the feeder
carriage (object feeder for component removal) of the tape feeder that requires the
removal of the mispicked component and the button in the "Direction" group box. After
that, press the [ENABLE] button. The selected feeder carriage moves to the place
accessible for the work to be performed.
(2) Press the [EMERGENCY STOP] switch.
(3) Open the feeder work area safety door (component replenishment section) and check
the object feeder.
• Remove the mispicked component from the object feeder.
When a pickup error has occurred in Feeder Carriage #4 ([F4]), the feeder
carriage cannot be moved to the place near the feeder work area safety
door.
Open the central safety door (feeder carriage cover) and check the object
feeder.
(Continued to the next page)
0509-002 2-116 AIM01ETRP
3.3 Error IDs and Remedial Procedures
Note