4OM-996-007 - 第314页

Error ID ltem Description 440801 Cutter THE CUTTER FORW ARD CONFIRMA TION W AS NOT ACTI- V A TED. ; BPH32 440802 Cutter THE CUTTER RETURN CONFIRMA TION WAS NOT ACTI- V A TED. ; BPH33 (Cause 1) A n opti cal b eam o f the …

100%1 / 417
Error ID ltem Description
440502 The Feeder Adhesive Tape The feeder adhesive tape lever moves despite being held by
stopper.
(Cause 1) Although the stopper was turned off while working, the lever moved down and the
optical beam of the sensor was shielded (not received).
(Remedy 1) Press the [RETURN] button to cancel the error display and remove the cause of
the error.
When the sensor is dirty and the optical beam is shielded (not received), wipe off
dirt on the sensor and then perform the zeroing operation on all axes.
440503 The Feeder Adhesive Tape The feeder adhesive tape lever does not move even though
stopper was open.
(Cause 1) Although the stopper was turned off while working, the lever did not move down and
the optical beam of the sensor was not shielded (received).
(Remedy 1) Press the [RETURN] button to cancel the error display and remove the cause of
the error.
When the sensor is dirty and the optical beam is shielded (not received), wipe off
dirt on the sensor and then perform the zeroing operation on all axes.
440601 Nozzle Change The nozzle change lever was not activated. ;BPH87 E/NR
440602 Nozzle Change The nozzle change lever moves despite being held by stop
per.
440603 Nozzle Change The nozzle change lever does not move even though stopper
was open.
Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
440701 Nozzle Change/Return The nozzle change/return lever was not activated.;BPH88 E/
NR
440702 Nozzle Change/Return The nozzle change/return lever moves despite being held by
stopper.
440703 Nozzle Change/Return The nozzle change/return lever does not move even though
stopper was open.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0509-002 2-119 AIM01ETRP
3.3 Error IDs and Remedial Procedures
Error ID ltem Description
440801 Cutter THE CUTTER FORWARD CONFIRMATION WAS NOT ACTI-
VATED. ; BPH32
440802 Cutter THE CUTTER RETURN CONFIRMATION WAS NOT ACTI-
VATED. ; BPH33
(Cause 1) An optical beam of the sensor was not shielded at all.
This error occurs when the cutter blades do not close completely.
Example: The cutter blades were damaged because they were activated to cut com-
ponents.
(Remedy 1) Press the [RETURN] button to cancel the error display and check the cutter
blades.
• If necessary, replace the cutter blades with new ones.
• Check the ON/OFF operation of the cutter forward movement check photosensor
(BPH32) and the cutter backward movement check photosensor (BPH33) in
the cutter section through the manual subsystem operation in the "MNL OPN."
window.
0509-001 2-119-1 AIM01ETRP
3.3 Error IDs and Remedial Procedures
(45 Recognition Communication)
Error ID ltem Description
450101 PEC INSPECT
450102 PEC INSPECT Time-Out Error
450103 PEC INSPECT GUI starting failure.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Zero all axes and re-start the operation.
When the machine cannot be set to its normal condition, consult our service
personnel for the remedy.
0509-002 2-120 AIM01ETRP
3.3 Error IDs and Remedial Procedures