4OM-996-007 - 第391页
4.3.3 P .E.C. Recognition Errors AA BB C DDDDD Detail Code Secondary Error Classification (1 to 4) Primary Error Classification (0 to 1) Classification (03) of Recognition Functions When an error ID other than the descri…
Recognition Error ID Recognition Error Contents, Cause, and Remedy
02**8000** Data Error
02**8001** Data Error in Process
02**8002** Error in Lighting Data
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Contact our service personnel for details.
02**9000** Other Errors
02**9001** Internal Processing Error
02**9002** Impossible to set the detection window.
02**9003** Impossible to set the window for arrayed lead end detection.
02 **9004** Impossible to set the window for lead detection at the corner.
02**9005** Impossible to set the window for lead detection.
02**9006** Angle Calculation Impossible.
02**9007** Internal Processing Error.
(Cause 1) Self-Diagnostics Error Message
(Remedy 1) Contact our service personnel for details.
4.3 Recognition Error IDs and Remedial Procedures
0509-002 2-206 AIM01ETRP
4.3.3 P.E.C. Recognition Errors
AA BB C DDDDD
Detail Code
Secondary Error Classification (1 to 4)
Primary Error Classification (0 to 1)
Classification (03) of Recognition Functions
When an error ID other than the described ones is issued, con-
tact our service personnel for some advice.
Table 4B16
Recognition Error ID Recognition Error Contents, Cause, and Remedy
0300100000 Specified Mark Not Found in Recognizable Range.
0300200000 Unstable Image around Fiducial Mark.
0300300000 Extensive Error in Similitude of Mark Shape.
0300400000 Extensive Error in Similitude of Mark Shape or Size.
0301100000 Specified Mark Not Found in Recognizable Range.
(Cause 1) The fiducial mark and the fiducial mark coordinates X and Y or the mark
data are not suitable.
(Remedy 1) Follow the steps below to reset the machine to the normal condition.
(1) When the [RETURN] button is pressed, the following recognition
window appears.
Fig. 4B26 Sample Display of Recognition Window
(Continue to the next page. )
4.3 Recognition Error IDs and Remedial Procedures
0509-002 2-207 AIM01ETRP
Note
(2) Manipulate the pointing device until the actual fiducial mark and the
template of the fiducial mark (located at the center of the crosshair)
overlap each other.
Note: Enlarge the view for accurate alignment operation. Otherwise,
components may not be placed accurately.
How to manipulate the pointing device
• Move the actual fiducial mark with the joy stick.
• Use the right button to enlarge the view.
• Use the left button to reduce the view.
Fig. 4B27
(3) After adjusting the actual fiducial mark and the template accurately,
press the right and left buttons of the at the same time.
The "AUTO OPN." window resumes.
When the [START] button is pressed, the automatic operation starts
again.
Pressing both right and left buttons at the same time is
validated only once.
If the actual fiducial mark and the template are not ad-
justed correctly, components may not be placed accu-
rately. In this case, follow the remedial operation described
below.
(3-1) Press the [STOP] button to stop the machine.
(3-2) Press the [Cancel] button to interrupt the automatic operation.
(3-3) Perform the zeroing operation on all axes.
(3-4) Open the "Run Mode" tab sheet. (Operation Sequence: [OPN.
MODE] Button Æ "Run Mode" Tab Sheet) Press the [SEMI-
AUTO (STEP)] button to re-start the automatic operation.
Fig. 4B28 Sample Display of Recognition Window
at Completion of Alignment Operation
4.3 Recognition Error IDs and Remedial Procedures
0403-002 2-208 AIM01ETRP
Note