4OM-1505-004_w.pdf - 第72页
4OM-1505 1-21 3. Maintenance Spots : Chap.1 Stencil Recognition X-Axis Ball Screw Every 6 Months Lubrication Stencil Recognition X-Axis Linear Guide Every 5 years Lubrication Apply grease with a brush or a spatula. Apply…
4OM-1505
1-20
3. Maintenance Spots : Chap.1
Every 5 years Lubrication
Squeegee Head Y-Axis Linear Guide
(One each in front and rear)
Inject new grease from the grease nipple
with a grease gun.
The used attachments should be
the U- and P-types or the SPK-3C.
Rear Side
Front Side
Note
Note
Note
Note
Note
If a large amount of grease is
applied, it may be dispersed
over a PCB and the stencil.
After applying grease, brush
the surface or scrape with a
spatula until a small amount
of grease remains on the
surface of the ball screw.
Every 5 years Lubrication
Squeegee Head Y-Axis Ball Screw
(Only on the right side)
Every Month Cleaning
Squeegee Head Y-Axis Linear
Guide (Right Side)
Do not leave any waste
threads after cleaning.
Every 5 years Lubrication
Squeegee Head Y-Axis Linear
Guide (Left Side)
Inject new grease from the grease
nipple with a grease gun.
The used attachments should
be the U- and P-types or the
SPK-3C.
Clean the stopper with an oiled rag.
Every Month Cleaning
Squeegee Head Y-Axis Linear
Guide (Left Side)
Do not leave any waste
threads after cleaning.
Apply grease with a brush or a
spatula.
Clean the stopper with an oiled rag.
F4A7
0906-001
4OM-1505
1-21
3. Maintenance Spots : Chap.1
Stencil Recognition X-Axis
Ball Screw
Every 6 Months Lubrication
Stencil Recognition X-Axis
Linear Guide
Every 5 years Lubrication
Apply grease with a brush or a
spatula.
Apply grease with a brush or a
spatula.
If a large amount of grease is
applied, it may be dispersed
over a PCB and the stencil.
After applying grease, brush
the surface or scrape with a
spatula until a small amount
of grease remains on the
surface of the ball screw.
Rear Side
Note
Clean the stopper with an oiled rag.
Every Month Cleaning
Stencil Recognition X-Axis
Linear Guide
Note
Do not leave any waste
threads after cleaning.
F4A8
Guide Bushing for Squeegee
Up/Down Movement
Every Month Cleaning
Clean the stopper with an oiled rag.
Do not leave any waste
threads after cleaning.
Guide Bushing for Squeegee
Up/Down Movement
Apply grease with a brush or a
spatula.
Every 6 Months Lubrication
Front Side
Note
F4A9
0906-001
4OM-1505
1-22
3. Maintenance Spots : Chap.1
3.2.3 Stencil Holder Section
Upper Surface of Stencil Holder
Every Day Cleaning
Wipe off dirt and dust accumulated
on the upper and side surfaces
with a rag.
Stencil Printing Pattern
Every Day Cleaning
After using the stencil, use an
ultrasonic cleaner (industrial
alcohol solvent) to clean the stencil
such that the mesh (pores) of
the stencil (stencil patterns) is
not clogged.
Lower Surface of Stencil
Every Day Cleaning
Clean the lower surface of
the stencil with a rag soaked in
industrial alcohol (solvent).
Front Side
F4A10
0906-001