ts9800-user-guide-7511-0360_A - 第5页

5 • When using the T S9 80 0 Jet Valv e with heater, please note that the tangible surfaces can be hot which can lead to severe burns. • The offered safety by th e appa ra tus can be affected by using parts/units not adv…

1. SAFETY

1.1 Intended Use

OK International cannot be responsible for injuries or damages resulting

from unintended applications of its equipment. Unintended uses may result

from taking the following actions:

• Making changes to equipment that has not been recommended in the

User Guide

• Using incompatible or damaged replacement parts

• Using unapproved accessories or auxiliary equipment

1.2 Safety Precautions

• Do not operate this unit in excess of maximum ratings/settings

• Always wear appropriate personal protective clothing or apparel

• This equipment is for indoor use only

1.3 Specified Normal Operation

• The TS9800 System can be used for dispensing fluids with a wide range

of fluid viscosity.

• Additional heating may only be carried out with a heating system from

Techcon Systems

• The usage of the TS9800 System can be carried out under laboratorial or

production environment.

• Provided the highest frequencies (up to 1500 Hz; average frequency

should not exceed 800 Hz) and parameter settings must be followed.

• The usage of media which affects the functioning of the TS9800 System

must be avoided.

1.4 Technical Details

• The usage of the TS9800 System is only allowed inside and up to 2000

meters above sea level.

• Relative humidity: maximum 80% at 31 °C, decreasing linear until 50%

at 50 °C.

• Fluctuation of the line voltage is not allowed over ± 10% of the nominal

voltage.

• Transient over voltage according to IEC 60364-4-443 will be tolerated:

degree of pollution 2 is allowed.

• The employed power cords must be accompanied by an earthing

equipment conductor. The used power sockets must be within safety

regulations. When using cable, which are not supplied by OK

International, the warranty of the TS9800 System will only range till the

operator interface.

• During installation and operation please pay attention to supply enough

air circulation: minimum distance above and below the system (valve

and control unit) are 1.5 cm. OK International advises a separate housing

which is in alignment of fire prevention covering EN 61010-1.

• When using the TS9800 Jet Valve with heater, please note that the

tangible surfaces can be hot which can lead to severe burns.

• The offered safety by the apparatus can be affected by using parts/units

not advised by OK International. The same can be considered for the

usage of dangerous substances or the operation in an explosive

environment, for which the TS9800 System is not designed for.

1.5 Warning Notices

• Never use the valve without nozzle insert or without fluid.

• Never disconnect the cables during the dispensing process.

• Avoid fast turning on and off to the control unit.

• Avoid long stand-by durations while the system is switched on.

• The TS9800 System is constructed modularly. If a defect occurs, the

effected module should not be interchanged with other parts. The whole

system needs to be sent back to Techcon Systems for repair. The cables

can stay with the customer but need to be checked. Information of how

to check the performance is available from Techcon Systems.

• Avoid hard placing of the valve on the working surfaces during

mounting and dismounting.

• Store the valve on a flat surface during the cleaning procedures. Do not

shake or bang the valve on any hard surface.

• For cleaning the valve, use a damp (isopropanol) cloth and make sure

that no fluid leaks into the valve (e. g. via connectors).

• Never connect the TS9800 Jet Valve to a control unit different than the

TS980 (connecting it to another control system will damage the valve).

• Check whether all fluid connections are attached and sealed.

• Make sure that all fluid contacting parts are stable against the fluid.

• Make sure that all electronic connections are connected and interlocked.

• Make sure the supply pressure does not exceed the admissible range.

• Make sure the maximum possible system pressure ranges between the

valve limit and the connection supplies limit - in no case above it.

• Check before the use of a heating device that the fluid does not tend to

unwanted reactions at elevated temperatures.

• When using a heating device make sure that the set temperature does not

exceed recommended temperature of the material (consult with the

material manufacture).

• When using a heating device please pay attention to the syringe/cartridge

feeding pressure.

• The heating of the TS9800 System cannot exceed 90°C.

• The TS9800 Jet Valve works with the normally-open concept.

Therefore, without supply voltage, the valve will open, and the fluid may

leak. To avoid leakage, disconnect air supply to the fluid syringe before

shutting down the control unit.

2. UNPACKING AND INSPECTION

Carefully unpack the valve and examine the items contained in the carton.

These will include:

Inspect the unit for any damaged which may have occurred in transit. If

such damage has occurred, notify the carrier at once. Claim for damage

must be made by the consignee to the carrier and should be reported to the

manufacturer.

1) Jet Valve TS9800 (version shown below is without heater)

2) Jet Valve Controller TS980

3) Nozzle Insert (order separately)

4) Actuator Cable (3-to-2 pin connectors)

5) Sensor Cable (6-to-5 pin connectors)

6) Heater Cable (4-pin connectors). This cable is available only if

the jet valve with heating system was ordered

7) Heat Guard with M6 mounting screw. These items are available

only if the jet valve with heating system was ordered

8) Syringe Bracket with M4 mounting screw

9) Nozzle installation tool

10) Nozzle adjustment tool

11) Tappet changing tool

12) Tappet seal tool

13) Wi-Fi antenna (Not available currently)

14) Power Supply

15) User Guide

Figure 1: TS9800 Jet Valve System