ts9800-user-guide-7511-0360_A - 第6页

6 2. UN PACKING AND INSPECTION Carefully unpack the valve a nd examine the items contained in the carton. These will in clude: Inspect the unit for a ny da maged which may have occurred in tra nsit. If such damage h as o…

• When using the TS9800 Jet Valve with heater, please note that the

tangible surfaces can be hot which can lead to severe burns.

• The offered safety by the apparatus can be affected by using parts/units

not advised by OK International. The same can be considered for the

usage of dangerous substances or the operation in an explosive

environment, for which the TS9800 System is not designed for.

1.5 Warning Notices

• Never use the valve without nozzle insert or without fluid.

• Never disconnect the cables during the dispensing process.

• Avoid fast turning on and off to the control unit.

• Avoid long stand-by durations while the system is switched on.

• The TS9800 System is constructed modularly. If a defect occurs, the

effected module should not be interchanged with other parts. The whole

system needs to be sent back to Techcon Systems for repair. The cables

can stay with the customer but need to be checked. Information of how

to check the performance is available from Techcon Systems.

• Avoid hard placing of the valve on the working surfaces during

mounting and dismounting.

• Store the valve on a flat surface during the cleaning procedures. Do not

shake or bang the valve on any hard surface.

• For cleaning the valve, use a damp (isopropanol) cloth and make sure

that no fluid leaks into the valve (e. g. via connectors).

• Never connect the TS9800 Jet Valve to a control unit different than the

TS980 (connecting it to another control system will damage the valve).

• Check whether all fluid connections are attached and sealed.

• Make sure that all fluid contacting parts are stable against the fluid.

• Make sure that all electronic connections are connected and interlocked.

• Make sure the supply pressure does not exceed the admissible range.

• Make sure the maximum possible system pressure ranges between the

valve limit and the connection supplies limit - in no case above it.

• Check before the use of a heating device that the fluid does not tend to

unwanted reactions at elevated temperatures.

• When using a heating device make sure that the set temperature does not

exceed recommended temperature of the material (consult with the

material manufacture).

• When using a heating device please pay attention to the syringe/cartridge

feeding pressure.

• The heating of the TS9800 System cannot exceed 90°C.

• The TS9800 Jet Valve works with the normally-open concept.

Therefore, without supply voltage, the valve will open, and the fluid may

leak. To avoid leakage, disconnect air supply to the fluid syringe before

shutting down the control unit.

2. UNPACKING AND INSPECTION

Carefully unpack the valve and examine the items contained in the carton.

These will include:

Inspect the unit for any damaged which may have occurred in transit. If

such damage has occurred, notify the carrier at once. Claim for damage

must be made by the consignee to the carrier and should be reported to the

manufacturer.

1) Jet Valve TS9800 (version shown below is without heater)

2) Jet Valve Controller TS980

3) Nozzle Insert (order separately)

4) Actuator Cable (3-to-2 pin connectors)

5) Sensor Cable (6-to-5 pin connectors)

6) Heater Cable (4-pin connectors). This cable is available only if

the jet valve with heating system was ordered

7) Heat Guard with M6 mounting screw. These items are available

only if the jet valve with heating system was ordered

8) Syringe Bracket with M4 mounting screw

9) Nozzle installation tool

10) Nozzle adjustment tool

11) Tappet changing tool

12) Tappet seal tool

13) Wi-Fi antenna (Not available currently)

14) Power Supply

15) User Guide

Figure 1: TS9800 Jet Valve System

3. TS9800 SYSTEM DESCRIPTION

The TS9800 Series Jet Valve is a Piezoelectric driven, non-contact

dispensing valve capable of handling fluid at different viscosities. Jet Valve

offers a fast jetting action producing hundreds of accurate deposits less than

one second.

Every component of the valve was designed to the highest tolerances and

manufactured to the strictest degree of precision insuring world class

accuracy and repeatability in drop-to-drop dispensing volume.

Jet Valve’s compact size and modular design aids integration into robotic

systems. The valve features fully adjustable parameter settings, allowing the

operator to change the jetting properties for different fluid types and

optimize the process for repeatable dispensing.

A variety of nozzles shape and sizes along with different tappet

configurations provides a wide spectrum of output jet deposits.