00197902-03_UM_X-Serie-S_EN - 第190页
3 Technical data and assemblies User manual SIPLACE X-Series 3.8 X feeder modules for SIPLACE X-Series From software version 710.0 Edition 12/2016 190 3.8.6.1 T echnical dat a 3 3.8.6.2 Number of waffle p ack trays per l…
User manual SIPLACE X-Series 3 Technical data and assemblies
From software version 710.0 Edition 12/2016 3.8 X feeder modules for SIPLACE X-Series
189
3.8.6 Tray holder for the component trolley of the SIPLACE X-Series
Item no. 00141285-xxTray holder for X-Series
3
Fig. 3.8 - 9 Tray holder
(1) Tray holder for SIPLACE X-Series
(2) Bracket for 2nd JEDEC waffle pack tray
(3) Waffle pack tray carrier
(4) Stop bar for the JEDEC waffle pack tray
(5) Locating pin - zero point of JEDEC waffle pack tray
3
Individually placed JEDEC waffle pack trays or waffle pack magazines can be fixed to the waffle
pack tray carrier with magnets. If two JEDEC waffle pack trays are placed, these will need to be
fixed into place with locking bars or mounting rails, as used for the MTC waffle pack tray carriers.
Parts: Item no.:
Magnet 00316593-xx
Locking bar/mounting rail for JEDEC magazines 00372615-xx
3 Technical data and assemblies User manual SIPLACE X-Series
3.8 X feeder modules for SIPLACE X-Series From software version 710.0 Edition 12/2016
190
3.8.6.1 Technical data
3
3.8.6.2 Number of waffle pack trays per location and machine
3.8.6.3 Inserting tray holder on the X-Series component trolley
Place the two front slider guides (item 1 in fig. 3.8 - 10, page 191) for the holder onto the in-
sertion aid (item 6 in fig. 3.8 - 10, page 191 ).
Push the holder along the guide profiles (item 7 in fig. 3.8 - 10, page 191), towards the front.
The holder slides with the front (item 1) and back slide guides (item 2 in fig. 3.8 - 10, page
191) on the guide profiles.
Continue pushing the holder, until the two centering pins "front" (item 4 in fig. 3.8 - 10, page
191) disappear into the centering holes (item 10 in fig. 3.8 - 10, page 191).
Check the two "back" centering pins (item 3 in fig. 3.8 - 10, page 191) for the holder. They
should slide easily into the recesses (item 8 in fig. 3.8 - 10, page 191) of the centering rail.
At the end stop of the holder, the locking latches (item 9 in fig. 3.8 - 10, page 191) engage
with the locking rollers (item 5) of the holder.
The waffle pack tray holder can be locked and released via the user interface. You can therefore
easily change the holder without interruption to machine operation.
Dimensions L x W x H 429 mm x 376 mm x 200 mm
Location occupied on the changeover table 32 locations
*a
*)a X feeder modules can be placed on the remaining 8 locations. When using locking bars/mounting rails, the
locations available are reduced to 6, due to the fixation lever which protrudes at the side.
Positioning options on X-Series placement ma-
chines
Locations 2 and/or 4
Placement head range TwinStar, CPP
*b
*)b Only permitted in high assembly position (CPP_H).
PLEASE NOTE
Further information
The maximum component height for the waffle pack tray holder depends on the maxi-
mum component height for the placement head used. When using waffle pack trays,
bear in mind that the components may not higher than the pickup height of a standard
feeder.
Placement machine Location 2 Location 4
X4 S 1 1
X3 S 2 1
X2 S 2 2
User manual SIPLACE X-Series 3 Technical data and assemblies
From software version 710.0 Edition 12/2016 3.8 X feeder modules for SIPLACE X-Series
191
3
3
Fig. 3.8 - 10 Using waffle pack tray holder on component trolley for X-Series
WARNING
Occupation of locations!
Always follow the safety instructions about occupying locations, in section 2.6.6
, page 99.
(1) Front slider guide (6) Insertion aid
(2) Back slider guide (7) Sliding rail (omega profile)
(3) "Back" centering pin (8) Recesses in the centering bar for holding the
"back" centering pin
(4) "Front" centering pin (9) Locking latches
(5) Locking roller (10) Centering holes on the changeover table for
holding the "front" centering pin