00194422-09_MM_X-Series_en - 第40页
Major Maintenance Maintenance Tasks for the Componen t Docking Unit 5.3.1 Tools, Co nsumables, Spare and Wear Parts 40 Maintenance Manual SIPLACE X Series 5.3 5 . 3 M a in t e n a n c e T a s k s f o r t h e C o m p o n …
Major Maintenance
5.2.3 Performing Maintenance Tasks Maintenance Tasks for Base Machine
Maintenance Manual SIPLACE X Series 39
5.2.3.7
5.2.3.7 Checking the Fans on the Computer Unit
Checking the Fans on the Computer Unit
5.2.3.8
5.2.3.8 Cleaning the Protective Covers
Cleaning the Protective Covers
NOTICE!
Machines with BoxPC
In BoxPCs, the fan is located in the computer and is mon
-
itored by this.
► Open the cover above the computer unit.
► Check the fan function (1) in the center of the comput
-
er unit. You should be able to hear the flow of air. If
the fan is defective, replace it.
► Now close the cover again.
► Check the protective covers for dirt.
► Clean them with a dry, lint-free cloth, if required.
► If the covers are very dirty, use a lint-free cloth and a
small amount of a neutral or weak alkaline cleaning
agent.
Clean the protective covers with light pressure and
take care not to damage the ESD coating!
CAUTION!
Selecting the right cleaning agent
The choice of cleaning agent for the protective covers
must be made with particular care so as not to damage
the ESD coating on the protective covers!
Do not use any chemical cleaning agents. Never use acid
or strong alkaline agents and avoid all ketones, esters,
aromatics, halogenated hydrocarbons, etheric oils or
similar.
Major Maintenance
Maintenance Tasks for the Component Docking Unit 5.3.1 Tools, Consumables, Spare and Wear Parts
40 Maintenance Manual SIPLACE X Series
5.3
5.3 Maintenance Tasks for the Component Docking Unit
Maintenance Tasks for the Component Docking Unit
5.3.1
5.3.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ ESD wristband [00320279-xx]
▪ Lint-free cloths [03082092-xx]
▪ SIPLACE cleaning cloth [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Klüberplex BEM 34-132 lubricant, 1 kg tin [00374565-xx]
▪ Lubrication nipple DIN71412-B-M6 – 45° bent (tape cutter) [03036943-xx], if required
▪ Grease gun with hose for Y axis (volume applied: approx. 0.4 g) [00374563-xx]
▪ 1 sheet of DIN A3 paper, or 2 sheets of DIN A4
▪ Adhesive tape strips
▪ Scissors
▪ Tweezers [00378525-xx]
▪ 2 brushes (Lubrication brush set 10 pieces [00370771-xx])
▪ Oil spray Surface Shield 400 ml [00328575-xx]
▪ Interflon Fin Grease [03020782-xx]
▪ Abrasive cleaning agent, universal 80x65mm [00372809-xx]
▪ UNISILKON L250L [00310259-xx]
▪ Rust prevention spray WD40, 400 ml [00325833-xx]
5.3.2
5.3.2 Preparatory Steps
Preparatory Steps
► Move the changeover tables out of the machine.
► Switch off the machine, disconnect it from the power supply and secure it to prevent unauthorized
reactivation. Observe the instructions in section "1.2 Preparatory Work..." [ ➙ 12].
See also
6.1 Filling the Grease Gun [ ➙ 59]
Major Maintenance
5.3.3 Performing Maintenance Tasks Maintenance Tasks for the Component Docking Unit
Maintenance Manual SIPLACE X Series 41
5.3.3
5.3.3 Performing Maintenance Tasks
Performing Maintenance Tasks
5.3.3.1
5.3.3.1 Function Test of Used Tape Cutter
Function Test of Used Tape Cutter
Risk of injury when working near the tap e cutter
► Take the sheet of paper out of the empty tape duct again.
If it has not been cut through accurately, the cutting blades must be cleaned or replaced. This task
must be carried out by authorized personnel. For removal and installation details, read the Service
manual.
WARNING
Risk of injury when working near the cutter.
When working in the area of the tape cutter, move the component trolley out of the machine
and disconnect the machine from the mains supply and the compressed air supply.
► Wait until the operating pressure has dropped to 0 MPa.
► Always secure the machine against unauthorized reactivation.
► Do not reach into the tape cutter.
Introducing paper (example of X-Series S)
➢ The machine and the changeover tables within the
machine must be switched on for the next test.
► Insert a sheet of DIN A3 paper or two DIN A4 sheets
attached to one another into the empty tape duct.
NOTICE!
A DIN A4 sheet on its own is too short to reach the tape
cutter.
► Attach the sheet of paper with adhesive tape to the
empty tape duct.
Make sure that there is no paper protruding upwards
in the placement head travel range.
► Start the cutting process in the software