00194422-09_MM_X-Series_en - 第54页
Major Maintenance Maintenance Work on the Gantry 5.5.3 Performing Maintenance Tasks 54 Maintenance Manual SIPLACE X Series 5.5.3.7 5 . 5 . 3 . 7 C h e c k in g t h e C o o lin g A ir H o s e s f o r t h e Y A x is Checki…
Major Maintenance
5.5.3 Performing Maintenance Tasks Maintenance Work on the Gantry
Maintenance Manual SIPLACE X Series 53
5.5.3.4
5.5.3.4 Cleaning the Linear Guides of the Y Axis
Cleaning the Linear Guides of the Y Axis
5.5.3.5
5.5.3.5 Cleaning the X Axis Scale
Cleaning the X Axis Scale
5.5.3.6
5.5.3.6 Cleaning the Y Axis Scale
Cleaning the Y Axis Scale
CAUTION!
Do not use any chemical cleaning agents!
Do not use additional lubricants. This may reduce the ser
-
vice life of the bearings.The guide rails are greased suffi
-
ciently by the guide carriage.
► Clean the linear guides for the Y axis thoroughly over
their entire length using lint-free cloths.
► Repeat this step for all linear guides.
CAUTION!
Always use soft cloths and minimal pressure to clean the
scales.
Dirty scales can lead to counting errors and, as a conse
-
quence, to machine stoppages.
► Clean the incremental scales (1) of the X axes with a
lint-free cloth soaked in ethanol.
CAUTION!
Always use soft cloths and minimal pressure to clean the
scales.
Dirty scales can lead to counting errors and, as a conse
-
quence, to machine stoppages.
► Clean the incremental scales (1) of the Y axes with a
lint-free cloth soaked in ethanol.
Major Maintenance
Maintenance Work on the Gantry 5.5.3 Performing Maintenance Tasks
54 Maintenance Manual SIPLACE X Series
5.5.3.7
5.5.3.7 Checking the Cooling Air Hoses for the Y Axis
Checking the Cooling Air Hoses for the Y Axis
CAUTION
Broken cooling air hoses
If the cooling air hoses are defective, the Y motor could overheat and cut out. Guide carriages
and guides may be damaged as a result.
NOTICE
This maintenance task is only required up to serial number B078.
► Loose the screw (1) fastening the cover plates above
the magnetic strip, which is in front of the trailing ca
-
ble.
► Remove the cover plates.
► Check the cooling air hoses for damage, particularly
in the vicinity of the cooling hose fixings in the trailing
chain. If the cooling air hoses are damaged, replace
them. For removal and installation details, read the
service manual for your machine.
► Fit the cover plates again.
► Repeat these steps for all cooling air hoses on all
gantries and replace the cooling air hoses where nec
-
essary.
Major Maintenance
5.6.1 Tools, Consumables, Spare and Wear Parts Maintenance Tasks for the Conveyor
Maintenance Manual SIPLACE X Series 55
5.6
5.6 Maintenance Tasks for the Conveyor
Maintenance Tasks for the Conveyor
5.6.1
5.6.1 Tools, Consumables, Spare and Wear Parts
Tools, Consumables, Spare and Wear Parts
▪ ESD wristband [00320279-xx]
▪ OIL Interflon Fin Super (teflon oil) [03017760-xx]
▪ Lint-free cleaning cloths [03082092-xx]
▪ Ethanol
Isopropanol – IPA can be used as an alternative.
▪ SIPLACE cleaning cloth [00315253-xx]
▪ Protective latex gloves [00372972-xx]
▪ Cotton gloves [00359087-xx]
5.6.2
5.6.2 Preparatory Steps
Preparatory Steps
Caution Conveyor - No PCB Must Be in the Conveyor
Note Co nveyor - Re commendation: Ad justing Sides via S oftware for Acces sibility
► Move the component trolley out of the machine.
See also
1.2 Preparatory Work... [ ➙ 12]
5.6.3
5.6.3 Performing Maintenance Tasks
Performing Maintenance Tasks
5.6.3.1
5.6.3.1 Cleaning and Preserving the Conveyor
Cleaning and Preserving the Conveyor
Preservi ng the Conveyor - Preparator y Tasks: Moving Sides Etc.
Moving the Conveyor Sides
► Move all conveyor sides to one side of the conveyor. Use the station software to set the dual con
-
veyor to single conveyor mode (right).
► First perform the following cleaning and preserving steps only to the side of the conveyor which is
now free.
CAUTION
No board
There must be no PCBs in the machine during the following tasks.
NOTICE
Accessibility
We recommend using the following procedure for better access:
► Use the station software to adjust the conveyor sides in such a way that you can easily
reach all conveyor belts as well as the whole area below the sides.
CAUTION
Observe the exact order
► Observe the following steps in exactly the order shown.
NOTICE
Keep the clamping surfaces clean
► During work, keep the clamping surface free of any dirt or oil. This makes subsequent
cleaning much easier.