2OM-1751-003w_G5S - 第102页
2OM-1751 1-50 1303-001 [5] EP Data 1invalid set Enable When the number of handling errors reaches the value set in [4], the production is stopped. Disable The EP data 1 count becomes invalid and the pick-up operation is …
2OM-1751
1-491303-001
4.2 "Opr.Mode" Tab Sheet
[1] Func Set
"Enable" or "Disable" can be selected to determine whether or not the
automatic teaching function should be used for the feeder pocket recognition.
[Disable] Button
Select this button not to use the automatic teaching function for the feeder
pocket recognition.
[Enable] Button
Select this button to use the automatic teaching function for the feeder pocket
recognition.
When the [Enable] button is selected for "Func Set" (automatic teaching
of feeder pocket recognition) in the "Tape Pocket Recog" group box, the
following buttons become available.
[2] Interval
When this button is pressed, the "Interval" window opens, enabling you
to specify the number of automatic teaching operations to be performed
periodically according to the number of tape feeding times for the feeder
pocket recognition.
[3] On Handling Err
One of the following buttons can be selected to determine whether or not
an automatic teaching operation should be performed on the feeder pocket
recognition after a pickup error has occurred.
Disable
Select this button not to perform an automatic teaching operation on the
feeder pocket recognition after a pickup error has occurred.
Enable
Select this button to perform an automatic teaching operation on the feeder
pocket recognition after a pickup error has occurred.
Note
This function is not available unless the "On Handling Err (Recog Time)"
is set to "1" or more.
[4] On Handling Err (Recog Time)
Set the feeder pocket recognition times when the "On Handling Err" has
been set to "Enable".
2OM-1751
1-501303-001
[5] EP Data 1invalid set
Enable
When the number of handling errors reaches the value set in [4], the
production is stopped.
Disable
The EP data 1 count becomes invalid and the pick-up operation is continued
without stopping the production.
[6] Recog when Exceeding Pickup Diff
Enable
When this button is selected, the component recognition determination is
performed. When the component pickup difference is larger than the value
set in the "[7] Comp size setting", the pocket recognition is performed.
Disable
When this button is selected, the component recognition determination is not
performed.
[7] "Comp. size setting" Group Box
The allowance of the component pickup difference in above "[6] Comp.
Recog. Detn" is set in this text box.
Comp size 0603 and less
The component size smaller than that of 0603 component, is set in this text
box.
0603 < Comp size <= 1005
The component size larger than that of 0603 component and smaller than that
of 1005 component, is set in this text box.
Comp size 1608 and beyond
The component size larger than that of 1608 component, is set in this test
box.
4.2 "Opr.Mode" Tab Sheet
2OM-1751
1-51
[8] Tape Joint Detection
One of the following buttons can be selected to determine whether or not
an automatic teaching operation should be performed on the feeder pocket
recognition after a tape joint line has been detected.
Disable
Select this button not to perform an automatic teaching operation on the
feeder pocket recognition after a tape joint line has been detected.
Enable
Select this button to perform an automatic teaching operation on the feeder
pocket recognition after a tape joint line has been detected.
[9] Recog Interval at Joint
When the operation is re-started, the interval time is set up in this data box in
the case that the feeder pocket recognition automatic teaching is performed
periodically, based on the tape feeding times.
[10] Pocket Recog Start Pos
The pocket recognition starting position is setup in this data box.
[11] Pocket Recog End Pos
The pocket recognition ending position is setup in this data box.
[12] Joint recog judge by comp recog
"Enable" or "Disable" is selected for the spliced tape joint detection function
in this selection box.
Disable
It is selected when the joint detection is not used.
Enable
It is selected when the joint detection is to be used.
[13] Joint tolerance
The joint allowance is setup in this data box, in the case of using the "Joint
Recognition Judgment" function.
1303-001
4.2 "Opr.Mode" Tab Sheet