2OM-1751-003w_G5S.pdf - 第334页

2OM-1751 6-62 1303-001 • Picking up the component automatically from each feeder to perform the component recognition test: Procedure (1) Select the test ID in the "COMP RCG" test window . (2) Press the [Fr .] …

100%1 / 380
2OM-1751
6-611303-001
(12) Execute the hysteresis test.
Reference
Refer to "7.3.4.1 Hysteresis Test
"
in chapter 6, Vol.2, in the Instruction
Manual for the Main Machine for the details.
(13) Press the [Dscd] or [Collect.] button and within 10 seconds, press the [START]
button on the operation panel.
Discard
: When selected, the discard operation is performed based on
the component discharge position data in the test ID.
Collection
: When selected, the head is moved to the lane No. specied
using the "Coll. Pos" button and the test component is
collected manually.
(14) Press the [ZERO] button and within 10 seconds, press the [START] button
on the operation panel.
(The XT beam will be returned to the home position and the test will be
ended).
7.3 "COMP RCG" Test Window
2OM-1751
6-621303-001
•
Picking up the component automatically from each feeder to perform the
component recognition test:
Procedure
(1) Select the test ID in the "COMP RCG" test window.
(2) Press the [Fr.] button. (The component recognition test window will be
displayed).
(3) Press the "Mnl." button for the "Pick-up mode".
Note
When the test ID is selected on the "Sel. From Comp Dt" tab sheet,
"Feeder" is selected for the "Pick-up mode".
(4) Select the head to be used for the component recognition using the button in
the "Head Sel" section.
(5) Press the [Fdr No.] button and enter the lane No. where the test component
pick-up is available.
(6) Press the [Noz select] button to select the nozzle No. to be used for the
recognition.
(7) Press the [Fr.] button.
(The head will be moved and the operation buttons will be changed).
(8) Press the [Recog] button and within 10 seconds, press the [START] button
on the operation panel.
(The test component will be picked up from the tape feeder).
(9) Press the [Recog] button and within 10 seconds, press the [START] button
on the operation panel.
(10) Conrm the recognition results in the "Results" pane.
•
When the recognition result is normal, go to the step (11).
•
When the recognition result is abnormal, go to the step (12).
(11) Conrm the component condition in the "Recognition Image Display"
section.
When any error is found in the component, replace it.
When there is no error in the component, conrm the data in the test ID and
correct it.
After that, perform the component recognition test again.
7.3 "COMP RCG" Test Window
2OM-1751
6-63
(12) Execute the hysteresis test.
Reference
Refer to "7.3.4.1 Hysteresis Test
"
in chapter 6, Vol.2, in the Instruction
Manual for the Main Machine for the details
(13) Press the [Dscd] or [Collect.] button and within 10 seconds, press the [START]
button on the operation panel.
Discard
: When selected, the discard operation is performed based on
the component discharge position data in the test ID.
Collection
: When selected, the head is moved to the lane No. specied
using the "Coll. Pos" button and the test component is
collected manually.
(14) Press the [ZERO] button and within 10 seconds, press the [START] button
on the operation panel.
(The XT beam will be returned to the home position and the test will be
ended).
1303-001
7.3 "COMP RCG" Test Window