2OM-1751-003w_G5S - 第79页

2OM-1751 1-27 1303-001 4.1.2 "Run Mode" Window ("Warm Start" Possible) When the machine is set in the "PAUSE" mode during the automatic operation, a warm start operation becomes possible and…

2OM-1751

1-261303-001

(4) When the [Start] button is selected, the designated step operation is

started.

Note

(a) Precautions during the step operation designated in "Any Step

Designation" mode.

•

The addition or deletion of step operation designated in the "Any

Step Designation" mode, is disabled. Before or after the component

placement, or after all applied steps are cancelled in the case of stop

in the course of the opeation, such addition or deletion is enabled.

•

In the case that the step designated in "Any Step Designation"

mode, is stopped in the course of the operation and the placement

is started again, the operation is started from the head of the undone

steps.

•

In the case that the operation is to be started again, after the step

designated in the "Any Step Designation" mode, is stopped in the

course of the operation and undone steps are cleared, the operation

is started from the head of the applied steps designated in "Any Step

Designation" mode.

•

Even when the PCB is discharged after the operation is stopped in

the course, the operated step data is not cleared.

(b) After all the steps are performed:

When the operation start is attempted after all the previously set steps

are performed, the component placement is not started. In order to

start the component placement, clear the previously set placement

steps.

Procedure

(1) Press the "Placement step clear" button in the

"Semi-Auto Any Desig" window.

(2) Press the "Release all step" button in the "Any

step designation" window and press the "Apply"

button.

(d) PCB Discharge

•

Discharge the PCB manually after all the steps designated in "Any

Step Designation" mode, are completed (including the stop in the

course of the operation).

•

Start the normal operation after the PCB discharge.

4.1 "Run Mode" Tab Sheet

2OM-1751

1-271303-001

4.1.2 "Run Mode" Window ("Warm Start" Possible)

When the machine is set in the "PAUSE" mode during the automatic operation, a

warm start operation becomes possible and the "Warm Start" window appears.

[1]

[2]

F2A21

[1] [Last Plc Pos Move] Button

When this button is pressed, the "Last Placement Point Check" window is

opened.

[2] [Cancel Warm Start] Button

When pressed, the warm start is cancelled.

Note

This button is displayed only in the window for the Supervisor, When the

Warm start has been stopped, the PCB is discharged without placing any

component in the re-start operation. Pay attention to it.

Reference

Refer to "5.3 Resumption of Production through Warm Start Procedure"

(Chapter 3 in Volume 1) for the detailed information on how to execute a

warm start operation.

4.1 "Run Mode" Tab Sheet

2OM-1751

1-281303-001

4.1.3 "Run Mode" Window in "Placement Recovery Available" Mode

"Enable" or "Disable" for the NL-axis Origin Teaching, is setup in this data box.

[1]

[2]

F2A22

[1] [Plc Pos Move] Button

When pressed, this button opens the "When the NL-axis origin teaching is

to be performed, the teaching time interval is selected from the following

items." window.

Reference

A pre-pick nozzle conrmation error will not occur when the pre-pick

nozzle conrmation function is not used.

Refer to "4.2 Opr. Mode Tab Sheet" in "Chapter 1" for how to use the pre-

pick nozzle conrmation function.

Note

When the machine is reset to its normal condition from the "ERROR"

window after a pre-pick nozzle conrmation error has occurred, the

"Placement Step Recovery" window appears automatically.

[2] [Cancel Place Rcvry] Button

When pressed, the placement recovery is cancelled.

4.1 "Run Mode" Tab Sheet