00195440-05-SG_D-Series_FSE-EN - 第176页

9 C&P Placement Heads 9.5 Settings 9.5.1 Boards at C&P12 176 Student Guide SIPLACE D-Series (FSE) 9.5.1.5 9 . 5 . 1 . 5 S P _ 1 2 D ig it a l I n t e r m e d ia t e D is t r ib u t o r [ 0 0 3 3 0 6 4 8 - 0 5 ] S…

9 C&P Placement Heads

9.5.1 Boards at C&P12 9.5 Settings

Student Guide SIPLACE D-Series (FSE) 175

9.5.1.3

9.5.1.3 Vision Board (Digital)

Vision Board (Digital)

The Vision processor board is mounted on the gantry head distributor board. This PCB is used for all

four gantries.

9.5.1.4

9.5.1.4 CAN 16 bit processor board (TQ module)

CAN 16 bit processor board (TQ module)

Description of 7-segment display (normal operation "." flashes):

▪ After switch ON the machine appears " 0 " on the display

▪ Display "b" --> BIOS was started.

▪ Display flashes alternatively between "b" and "." --> no application available or unable to start appli-

cation.

▪ Display " -I " and " I- " application was loaded.

▪ "." flashes on the display --> ready for operation.

Vision board

Legend

1. X8 Connector illumination and video signals PCB

camera

2. X3 Connector illumination and video signals compo-

nent camera

3. LEDs P15V - 15Volt / Vcc - Power supply Vision

board

4. DIP switch

5. CAN processor 16 bit (TQM module)

6. Connector X22 - X25 - Connectors for the video cable

to the trailing cable

7. Connector X11 for download

8. Voltage supply 11 VDC, measurable

16 bit processor (TQ module)

Legend

1. 7 Segment display

2. LED for manual RESET of processor

3. 16 bit processor

The 16 BIT CAN processor is used for various different

functions in the following units:

(see chapter communication and control too)

▪ Visionboard, communication and control via the CAN

Bus to the Vision computer.

▪ Gantry head distributor, control of head processes

and vacuum

9 C&P Placement Heads

9.5 Settings 9.5.1 Boards at C&P12

176 Student Guide SIPLACE D-Series (FSE)

9.5.1.5

9.5.1.5 SP_12 Digital Intermediate Distributor [00330648-05]

SP_12 Digital Intermediate Distributor [00330648-05]

The following supply voltages and signals are routed by the intermediate distributor to the individual

placement head modules or to the head board:

Intermediate distributor

Legend

1. Intermediate distributor

2. Spacer bolt M3x10

3. Spacer bolt M3x10

4. Spacer bolt M3x10

5. Spacer bolt M3x10

6. Front section of C&P head

7. Connectors X1 and X2 (on the rear side)

The intermediate distributor (1) is fixed to the front part (6)

with four spacer bolts (items 2, 3, 4 and 5). The pressure

sensor is located above the spacer bolts (5), on the back

of the intermediate distribution board. The cover of the in-

termediate distributor is fixed with push buttons.

Position of the sockets

Legend

1. Front of the intermediate distributor

2. Back of the intermediate distributor

U4 = pressure sensor

Two 40-pin ribbon cables run from plug X1 and X2 on the

intermediate distributor to socket X14 / X13 on the head

board.

9 C&P Placement Heads

9.5.2 Overview of Settings on the C&P6/12 9.5 Settings

Student Guide SIPLACE D-Series (FSE) 177

9.5.2

9.5.2 Overview of Settings on the C&P6/12

Overview of Settings on the C&P6/12

Connectors Description

X1, 40-pole Connected to plug X14 on the head board

▪ Voltage supply, tacho and track signals for the Z axis drive

▪ Signal from light barrier "Z axis in top position"

▪ Signal from light barrier "Z axis in bottom position" (sensor stop signal)

▪ Control signal for the air blast valve

▪ Supply voltage +5 VDC, ±15 VDC

▪ Reference point signal for the DP axis

▪ Track signals for the DP axis

X2, 40-pole Connected to plug X13 of the gantry head distributor

▪ Voltage supply and track signals for the star axis drive

▪ Reference point for the star axis

▪ Analog air blast pressure value

▪ Supply voltages +5 VDC, ±15 VDC, +24 VDC

X3, 10-pole Connection for the Z motor and Z tacho signal (tacho signal is not used on

the HF machine)

X4, 10-pole Connection for the Z axis track signals

X5, 10-pole Connection for the star motor

X6, 6-pole Connection for the air blast valve

X7, 10-pole Connection for the DP axis track signals

X10, 10-pole Connection for the "Z axis up" signal

X11, 8-pole Connection for the light barrier "Z axis down" signal (sensor stop signal)

X12, 10-pole Connection for the star axis track signals

X13, 10-pole Test connection for the Z axis track signals

X14, 10-pole not used

X15, 10-pole Test connection for the star axis track signals

X16, 10-pole Test connection for the DP axis track signals

Description Tools and equipment Values

Mount the star onto the motor

shaft of the star motor

Adjust with the power pack and

star zero point gauge

Check the magnetic neutral posi-

tion in SITEST

(max. deviation 95 digits)

Determine zero point correction

for the star.

Gauge for zero point correction /

SITEST

Enter result of zero point correc-

tion with SITEST

--> enter positions.

Switch position on star motor

(resolution of track signals 10 -

25)

none HF/X/D machines at switch posi-

tion 25

DP axis incremental encoder ad-

justment to the glass scale (seg-

ment)

Test probe 1.4 - 1.6 mm Distance 1.5 mm.

Adjustment mechanical position

of valve positioning drives

Distance gauge 0.2 mm or ad-

justment plunger

0.2 mm distance plunger to the

valve frame

Light barrier Z axis down Test probe 1.0 mm Distance 1.0 mm.

Clamping device on Z belt --- Tension jack must lie on the belt

teeth at the top and bottom.