00195440-05-SG_D-Series_FSE-EN - 第224页
12 Modular Conveyor 12.3 Conveyor Settings 12.3.1 Setting the Fixed Conveyor Side (S ingle and Dual Conveyor) 224 Student Guide SIPLACE D-Series (FSE) ► The fixed conveyor side TSP lane 1 (right side fixed (lane 2 left s…
12 Modular Conveyor
12.3.1 Setting the Fixed Conveyor Side (Single and Dual Conveyor) 12.3 Conveyor Settings
Student Guide SIPLACE D-Series (FSE) 223
► Loosen the lockscrew(s) (4) and use a screwdriver to push the hexagonal circlip over the shaft on
lifting table 1.
► Do this for lifting tables in all placement areas. (lifting tables in the PA’s 180° turned.)
► Configure the new conveyor mode in SIPLACE Pro
To (3): Converting the Single Conveyor Mode Back to Flexible Dual Conveyor Mode
► Select the SITEST conveyor menu "Option and configuration" and then click on Widen conveyor to
set the standard conveyor mode.
► The flexible conveyor side of conveyor 1 (right side fixed (track 1 left side fix)) is moved to a small
conveyor width.
► The SITEST SW ask to disconnect the lifting tables - Do so-.
► The SITEST SW will now use the conveyor control SW to move the fixed side of conveyor 2 (right
side is fixed (lane 1 left side fixed)) back to its standard position. Check the distances between the
two fixed conveyor lanes.
► Now adjust conveyor width of both tracks to desired values.
To (2): Setting the Fixed Conveyor Side for "Extra Wide" Mode
This mode is set in the menu Change position of fixed rail in the software.
The default positions for the fixed conveyor side (s) are predefined.
► Select Option and configuration from the SITEST conveyor menu and then click on Change position
of fixed rail, to set the mode "extra wide".
► The fixed conveyor side TSP 2 (right side fixed (lane 1 left side fixed) remains in its position.
Lifting table
▪ The drive shaft (1) is connected to the piston rod of
the pneumatic cylinder. This shaft couple the second
lifting table of the dual conveyor. The lifting table drive
shaft also has an additional rod with a hexagonal cir-
clip. They secure the sleeve shaft in the desired posi-
tion.
▪ Direction of transport (2)
▪ Direction (3) in which the hollow shaft from lifting ta-
ble 2 (1 in PA 2) is to be moved to lifting table 1 (2 in
PA 2).
▪ Lock screws (4)
NOTICE
When converting the dual conveyor to a single conveyor (flexible dual conveyor, connect the
lifting tables when requested to do so by SITEST (we recommend doing this without com-
pressed air supply to the lifting table).
This function is supported by SIPLACE Pro.
NOTICE
Cause of Hazard
This mode is possible for D/Di-series machines with single or dual conveyors.
12 Modular Conveyor
12.3 Conveyor Settings 12.3.1 Setting the Fixed Conveyor Side (Single and Dual Conveyor)
224 Student Guide SIPLACE D-Series (FSE)
► The fixed conveyor side TSP lane 1 (right side fixed (lane 2 left side fixed) is moved 34 mm outwards.
The flexible conveyor side TSP lane 2 (lane 1 left fixed) can now be set to accommodate boards
which are wider than 216 mm (242 mm).
12.3.1.2
12.3.1.2 Setting the Fixed Conveyor Side (Single and Dual Conveyor)
Setting the Fixed Conveyor Side (Single and Dual Conveyor)
Moving the fixed conveyor side of lane 2 (D1/D1i/D2/D2i)
CAUTION
Cause of Hazard
The end stoppers between the gantries need to be replaced with thinner stoppers, otherwise
you will not be able to perform placement on the fixed side, parallel to the pickup process in the
2nd gantry.
The lubrication nipples in the Y guidance slider are to be replaced with socket-head screws,
otherwise these could be damaged by a gantry crash.
CAUTION
Cause of Hazard
After the conversion, you need to measure or calibrate the PCB reference corner and the con-
veyor sides and then save these values in the machine data.
NOTICE
Cause of Hazard
The setting values for the fixed conveyor side must be checked after the conveyor side fixation
is released. If these values are not correct for the single or dual conveyor, the placement refer-
ence corner could be displaced. In turn, this leads to fiducial recognition errors.
12 Modular Conveyor
12.3.1 Setting the Fixed Conveyor Side (Single and Dual Conveyor) 12.3 Conveyor Settings
Student Guide SIPLACE D-Series (FSE) 225
Legend
Procedure:
► Check the measurements . (See following diagram).
Setting the "fixed conveyor side"
► Insert the spring and tighten the screw fastening the brake.
(1) Fixed side - conveyor lane 1 (2) Fixed side - conveyor lane 2
(3) Side flange with grub screw (4) Fastening screw
(5) Fixed side - conveyor lane 2 - moving (T) Transport direction
NOTICE
Cause of Hazard
You do not normally need to adjust the fixed side. One exception is when service work involves
prior movement of the fixed conveyor side.
Modular conveyor detail
► Loosen the fastening screw (1) on the side flange.
► This fastening screw (1) has a socket-head grub
screw inside which needs to be loosened slightly - do
not unscrew completely!
► Remove the fastening screw (1). Watch the spring in-
side.