00195440-05-SG_D-Series_FSE-EN - 第261页
15 SIPLACE Measuring Tools 15.1 SIPLACE Axis Tester (SAT) [03002801-01] Student Guide SIPLACE D-Series (FSE) 261 15 1 5 S I P L A C E M e a s u r in g T o o ls SIPLACE Measuring Tools See also 16.1 Overview of Calibr…
14 SITEST
14.4 Room for Your Sketches and Notes 14.3.7 New Functions in SITEST
260 Student Guide SIPLACE D-Series (FSE)
15 SIPLACE Measuring Tools
15.1 SIPLACE Axis Tester (SAT) [03002801-01]
Student Guide SIPLACE D-Series (FSE) 261
15
15 SIPLACE Measuring Tools
SIPLACE Measuring Tools
See also
16.1 Overview of Calibration Tools [ ➙ 265]
15.1
15.1 SIPLACE Axis Tester (SAT) [03002801-01]
SIPLACE Axis Tester (SAT) [03002801-01]
Axis tester - view from above
Legend
1. LCD display with 240 x 128 pixels, black-and-white display, with background illumination
The LCD display shows the menus and the recorded trigger, track and position signals. All relevant
parameters, such as
– Time basis,
– Time measurement values,
– Signal levels and
– Cursor positions with the corresponding time deviation values
are shown as alphanumerical data in the diagram of the measurement curves.
2. Dynamic function display of BNC socket arrangement on the LCD display
3. Dynamic function display of foil button arrangement on the LCD display
4. Five foil buttons for menu control
5. Green LED for displaying operation
NOTICE
The axis tester is designed for all machines with A363. This function is limited for machines with
A364.
15 SIPLACE Measuring Tools
15.1 SIPLACE Axis Tester (SAT) [03002801-01]
262 Student Guide SIPLACE D-Series (FSE)
Axis tester - view from below
Legend
1. Connection for flat ribbon cable:
– At the axis tester end:
– 37 pin Sub-D connector
– At the axis control end:
– 37 pin Sub-D connector for the S-20/23/25/F4/F5 and HS-50 machines, with the axis control
units A361 or A362
– 25 pin Sub-D connector for the S-15/F3, G machines and the wafflepack changer, with the axis
control unit A360
An adapter is attached to the flat ribbon cable for connection of the 25 pin axis control. The op-
erating voltages of +5 V- ±5 % and ±15 V- ±5 % are fed via the 37 pin flat ribbon cable from the
axis control unit to the axis tester.
2. 9 pin Sub-D connector for CAN Bus cable e.g. for connection of CAN Bus controlled boards in the
machine – currently not used (transmission rate 128 kBaud to 1 MBaud, impedance 120 Ohm)
3. 9 pin Sub-D connector for the serial interface cable (V24) needed for software downloads, e.g. for
connection of an external PC (max. transmission rate up to 188 kBaud)
4. Four BNC sockets, connection impedance 50 Ohm. Socket assignment can be programmed. The
following signals can be assigned:
– Track signal A or B TTL level, max. 5 V
– Zero pulse TTL level tmin = 1 µsec
– End position signal TTL level tmin > 10 msec
– Trigger TTL level tmin > 10 msec
– Count error TTL level, trigger signal from count error sensor of oscilloscope
– Vtarget ±10 V, analog signal, Ri = 10 kOhm
– Force ±10 V analog signal, Ri = 10 kOhm
– VREG (resulting current) ±10 V analog signal, Ri = 10 kOhm
– Position deviation ±10 V analog signal; signal generated internally in axis tester.