80S-15贴片机 - 第414页

9 Revolver Head SIPLACE 80S/F/G Service Manual Edition 04/97 9 - 130 ● After assem bly, te st the dynam ic behav ior and func tioning of the dR axis dri ve with refe rence to th e adjust- ment instr uc tions and usin g t…

100%1 / 484
SIPLACE 80S/F/G Service Manual 9 Revolver Head
Edition 04/97
9 - 129
9.17 Service work on the dR axis
9.17.1 Tools, equipment and consumables
9.17.2 Spare parts
9.17.3 Replacing the DC motor / tacho unit
●
Dismantle the encoder housing as described in Section 9.13 on page 9 - 103.
●
Unplug the combined DC motor / tacho (see item 1 in Fig. 9.17.1) from slot X10 (see item 2 in Fig. 9.17.1)
on the ’Head’ conversion board Y0303.
●
Loosen the 3 M3x8 fillister head screws (see item 6 in Fig. 9.17.1) for fixing the motor.
●
Change the combined DC motor / tacho.
PLEASE NOTE:
Be careful not to stretch or damage the toothed belt.
●
Fix the combined DC motor / tacho in place
●
Check the toothed belt tension using the belt tension measuring device and the ’Measuring the belt ten-
sion’ user’s manual. If the toothed belt is tensioned correctly, the frequency should be 405 ± 35 Hz.
●
Plug the combined DC motor / tacho into slot X10.
From item number
Set of hexagon socket spanners
Set of screwdrivers
SIPLACE segment changing device, version I
00310699-01
SIPLACE segment changing device, version II
00305897-02
Segment case
00302217-01
Segment mount LTX for the SIPLACE 80S-15/F3 revolver head
00329262-01
Housing retainer
00306798-01
SITEST program
Adjustment instructions
Circuit diagrams
Belt belt tension measuring device, complete
00326015-01
Cable ties
From item number
DC motor / tacho unit with disk
00327787S01
Synchroflex 10 M2, 032/256 toothed belt
00303931S01
9 Revolver Head SIPLACE 80S/F/G Service Manual
Edition 04/97
9 - 130
●
After assembly, test the dynamic behavior and functioning of the dR axis drive with reference to the adjust-
ment instructions and using the SITEST program.
Fig. 9.17.1 DC motor / tacho unit for the dR axis
Key to Fig. 9.17.1
1 Combined DC motor / tacho, dR axis
2 Slot X10 for connecting the dR axis motor
3 Encoder housing
4 AL 14 M/112-0 synchronizing disk
5 Synchroflex 10 M2, 032/256 toothed belt
6 3 M3 x 8 fillister head screws
4
5
1
6
2
3
SIPLACE 80S/F/G Service Manual 9 Revolver Head
Edition 04/97
9 - 131
9.17.4 Replacing the drive toothed belt
●
Dismantle the encoder housing as described in Section 9.13 on page 9 - 103.
●
Loosen the 3 M3 x8 fillister head screws (see item 6 in Fig. 9.17.1) for fixing the motor.
●
Replace the defective toothed belt.
PLEASE NOTE:
Be careful not to stretch or damage the toothed belt.
●
Fix the combined DC motor / tacho in place.
●
Check the toothed belt tension using the belt tension measuring device and the ’Measuring the belt ten-
sion’ user’s manual. If the toothed belt is tensioned correctly, the frequency should be 405 ± 35 Hz.
●
After assembly, test the dynamic behavior and functioning of the dR axis drive with reference to the adjust-
ment instructions and using the SITEST program.