80S-15贴片机 - 第430页
9 Revolver Head SIPLACE 80S/F/G Service Manual Edition 04/97 9 - 146 Fig. 9.19.4 Connec ting the BERO to the plug Key to Fig . 9.19.4 ● Set the op erating d istan ce to 0.2 m m as d escribed f or scr ewdrive r 1 (see F i…
SIPLACE 80S/F/G Service Manual 9 Revolver Head
Edition 04/97
9 - 145
9.19.6 Replacing the BERO
Fig. 9.19.3 BERO of screwdriver 2
Key to Fig. 9.19.3
●
Loosen the M 1.6 x 4 fillister head screws (see item 3 in Fig. 9.19.3) for clamping the BERO.
●
Pull the connecting wires out of the plug.
●
Connect the BERO cable to the plug using the locking clip contacts as shown in the following diagram:
1 3RG 4603-2AB00/3.0 mm/SN = 0.6 mm/1S BERO
2 Toothed wheel holder
3 M 1.6 x 4 fillister head screws for clamping the BERO
3
2
1
9 Revolver Head SIPLACE 80S/F/G Service Manual
Edition 04/97
9 - 146
Fig. 9.19.4 Connecting the BERO to the plug
Key to Fig. 9.19.4
●
Set the operating distance to 0.2 mm as described for screwdriver 1 (see Fig. 9.18.5 on page 9 - 138 and
the text below).
●
Clamp the BERO in this position.
●
When assembling the head, make sure that you align the screwdriver blade (see item 4 in Fig. 9.19.2 on
page 9 - 143) with the 30° mark. If it is not aligned, the star will not be able to turn the segments after
assembly.
●
After assembly, check the functioning of the screwdriver with reference to the adjustment instructions and
using the SITEST program.
2 BERO cable: brown B1 BERO
3 BERO cable: blue X1 Plug for slot X17 on conversion board Y0005
6 BERO cable: black (see Fig. 9.12.1 on page 9 - 98)
M
+-
B1
X1
456123
SIPLACE 80S/F/G Service Manual 9 Revolver Head
Edition 04/97
9 - 147
9.19.7 Replacing the miniature ball bearing, spring washer and toothed
wheel 2 ’reject’
Fig. 9.19.5 Replacing the miniature ball bearing, spring washer and toothed wheel 2 ’reject’
Key to Fig. 9.19.5
●
Loosen the M1.6x4 BERO clamping screw.
●
Pull the BERO out of the hole.
●
Loosen the two M2x6 fillister head screws (see item 7 in Fig. 9.19.5) for fixing the toothed wheel holder
(see item 5 in Fig. 9.19.5).
●
Carefully pull the toothed wheel holder away from the parallel pins.
●
Replace the miniature ball bearing, spring washer or toothed wheel 2.
●
Align the screwdriver blade with respect to toothed wheel 1 as shown in Fig. 9.19.2 on page 9 - 143.
●
Fix the toothed wheel holder in place.
1 5x8x2.5 MF85 ZZS miniature ball
bearing
5 Toothed wheel holder
2 Spring washer FS 8 x 10 6 M1.6x4 fillister head screw for clamping the BERO
3 Toothed wheel 2 - reject 7 M2x6 fillister head screw for fixing the toothed wheel
4BERO holder
4
5
1
1
2
3
6
7
7