80S-15贴片机 - 第481页
11 Control Unit SIPLACE 80 S/F/G Service M anual Edition 04/97 11 - 12
SIPLACE 80 S/F/G Service Manual 11 Control Unit
Edition 04/97
11 - 11
11.5 Wrap Connections of Machine Controller MC2
(right-hand side, applies to 80S only)
11.5.1 KSP-M18-A16 C8451-A45-A51-X Machine Controller
The following jumpers must be present:
NOTE:
Wrap connections which differ from the standard configuration are marked by an asterisk (*).
Connection Significance
WM1/11
→
WM1/12 Operation without 80C187 co-processor
WM2/11
→
WM2/12 AMS-INIT connected to assembly
WJ2/1
→
WJ2/2 SRAM and DPRAM connected to Vcc
WC2/1
→
WC2/2 SMP HOLD sets M18 to HOLD
WM4/2
→
WM1/2 Interrupt MOD1 on IR2 Master
WM4/3
→
WM2/5 Interrupt SCC on IR3 Master
WM4/4
→
WM1/1 Interrupt MOD0 on IR4 Master
WM4/6
→
WM2/2 Interrupt WAKEUP on IR6 Master
WM4/7 *
→
WK2/7 Interrupt AMS-INT6 on IR7 Master
WM2/6 *
→
WK2/5 SOFTINT on AMS-INT4
WC1/1
→
WM1/6 SCC-Clock, 4.91 MHz
WJ3/1
→
WJ3/6 WAKEUP on IO address 1000H
WF2/2
→
WF2/4 32K DPRAM in upper half of segment
WN2/1
→
WN2/2 DPRAM address on AMS bus 50000H
WN2/2
→
WN2/4 DPRAM address on AMS bus 50000H
WJ1/1
→
WJ2/5 0 waitstates command delay
WJ1/4
→
WJ2/6
4 waitstates command delay for SMP bus
access
WJ1/4
→
WJ2/7
WJ1/4
→
WJ2/8
WF1/2
→
WF1/3 V24 D2 on SCC
WM3/9
→
WM4/10 64 Kilobyte EPROMs
WM3/10
→
WM4/11 64 Kilobyte EPROMs
WM3/11
→
WM4/12 64 Kilobyte EPROMs
Tab. 11.5 - 1 Wrap connections of the KSP-M18-A16 C8451-A45-A51-X machine controller
11 Control Unit SIPLACE 80 S/F/G Service Manual
Edition 04/97
11 - 12
SIPLACE 80S/F/G Service Manual 12 Vision Systems
Edition 04/97
12 - I
Contents
Page
12 Vision Systems
12.1 Removing and Installing the Component Change-over Table . . . . . . . . . . . . . . . . . . . . 12 - 3
12.1.1 Tools required. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 3
12.2 Replacing the IC Vision Camera and Illumination Control Board (SIPLACE 80F) . . . .12 - 5
12.2.1 Tools, inspection, measuring and test equipment required . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 5
12.2.2 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 5
12.2.3 Removing the IC vision camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 6
12.2.4 Removing the IC illumination control board Y0043 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 7
12.2.5 Fitting the IC vision camera and illumination controller . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 7
12.2.6 Setting work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 7
12.3 Replacing the Flip-chip Vision Camera and Illumination Controller (SIPLACE 80F). . 12 - 9
12.3.1 Tools, inspection, measuring and test equipment required . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 9
12.3.2 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 9
12.3.3 Removing the flip-chip vision camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 9
12.3.4 Removing the flip-chip illumination control board Y0043 . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 11
12.3.5 Fitting the flip-chip vision camera and illumination controller . . . . . . . . . . . . . . . . . . . . . . . 12 - 11
12.3.6 Setting work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 11
12.4 Replacing the Coplanarity Laser Module (SIPLACE 80F). . . . . . . . . . . . . . . . . . . . . . . 12 - 13
12.4.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 13
12.4.2 Tools, inspection, measuring and test equipment required . . . . . . . . . . . . . . . . . . . . . . . . 12 - 14
12.4.3 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 14
12.4.4 Removing the coplanarity module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 14
12.4.5 Installing the coplanarity module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 14
12.4.6 Setting work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 15
12.5 Replacing the Undergantry PCB Camera (SIPLACE G) . . . . . . . . . . . . . . . . . . . . . . . . 12 - 16
12.5.1 Tools, inspection, measuring and test equipment required . . . . . . . . . . . . . . . . . . . . . . . . 12 - 16
12.5.2 Spare parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 16
12.5.3 Removing the PCB undergantry camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 16
12.5.4 Installing the PCB undergantry camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 17
12.5.5 Setting work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 17