SU_UM_TME20822_EN.pdf - 第18页

18 Smart-UPS S MTL 22 00/3000 RMI2UC/RMI2UCNC Op e ra t i on EN TME2 08 22 – 08/2 023 Operation Usi ng the disp lay These Smart-UPS models are equipped with an intuitive and configurable LCD display . This di spl ay comp…

100%1 / 34
17
Connect and Install Management Software
Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC
EN TME20822 – 08/2023
Connect and Install Management Software
Smart-UPS is provided with PowerChute UPS Management Software for unattended
operating system shutdown, UPS monitoring, UPS control and energy reporting. The
following diagram is a representation of a typical server installation.
USB Port
Serial Port
Connect the USB cable from the rear of the UPS to the protected device such as a
server.
For a server or other device with an operating system, download and install latest
version of the PowerChute Serial Shutdown from https://www.apc.com/pcss.
PowerChute Serial Shutdown supports graceful shutdown in the event of an
extended power outage.
NOTE: PowerChute is a 64-bit only application and cannot be installed on a 32-bit
operating system.
A built-in Serial port is also available for additional communication options with
serial cable.
NOTE: Serial and USB cannot be used at the same time.
Even more communication options are available via the built-in Smartslot. Refer to
www.apc.com for more information.
TM
SERIAL SHUTDOWN
18
Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC
Operation
EN TME20822 – 08/2023
Operation
Using the display
These Smart-UPS models are equipped with an intuitive and configurable LCD
display. This display complements the software interface as they convey similar
information and either may be used to configure the UPS settings.
The display consists of the following keys and indicators:
The display has two main display/menu options – standard and advanced.
Note: The standard menu is the default setting and does not contain all of the menus
and attributes of the advanced menu. The advanced menu automatically scrolls
through multiple screens.
UPS ON/OFF Button This button is used to turn the UPS output power on and off.
Quick status LEDs
On-line LED The Online indicator illuminates green when UPS output is
turned on and operating on AC power.
On-battery LED The On-battery indicator illuminates orange and the unit
will continue to emit a series of short beeps indicating that
the UPS is operating on battery power.
Error detected LED The Error detected LED will illuminate red if the unit
detects an error condition. The display screen may also
indicate an error message or code.
Replace battery LED The Replace battery indicator illuminates red when the
UPS battery does not pass self test and requires
replacement.
ESCAPE key The ESCAPE key always returns the display to the previous
screen. It is used to exit the various display menus.
ENTER key The ENTER key is used to confirm a selection and/or enter a
menu.
UP/DOWN keys UP and DOWN keys are used to navigate through each menu
selection.
Standard Menu Display
Advanced Menu Display
su0983a
Load: 18%
Batt: 100%
su0984a
On Utility
Efficiency: 98%
19
Operation
Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC
EN TME20822 – 08/2023
Standard menus
The Standard menus are the most commonly used menus. The following is a list of
some items displayed in this menu mode. Visit apc.com for additional details.
Menu General Functions
Status View UPS information:
• Operating Mode
• Efficiency
• Load Power
• Load VA
• Battery Charge state
• Estimated Runtime
•Battery Temp
• Input
• Output
• SmartConnect
• Probe 1, Probe 2, when NMC
and sensor probes are
installed
Configuration Configures UPS settings:
• Language
• Green Mode
• Local Power Quality: Good,
Fair, Poor
• Menu Type: Standard or
Advanced
• Audible Alarm
• Display (Auto Dim, Auto Off,
Always On)
• Reset to Factory Default
• SmartConnect Control
•Install FW?
Note: Enabled only if a
firmware update is available.
Test & Diags Performs UPS tests and
diagnostic functions:
• UPS Self Test
• UPS Alarms Test
About View UPS information:
• UPS Model
• UPS Part No.
• UPS Serial No.
• UPS Manufacture Date
•Battery Part No.
• Battery Install Date
• Replace Battery by
• Running UPS FW
• Available UPS FW
Note: Enabled only if a UPS
firmware update is available.
•UPS MAC
• UPS IP Address
• UPS Product Key
• SmartSlot Card (if installed)