SU_UM_TME20822_EN.pdf - 第21页

21 Operat ion Smart-UPS SMTL 220 0/3000 RMI2UC/RMI2UCNC EN T ME2 0822 – 08 /202 3 About View UPS information: • UP S Model • UPS Part No. • UPS Seri al No. • UPS Manuf acture Date • Battery Part No. • Bat ter y Inst all …

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

Operation

EN TME20822 – 08/2023

Advanced menus

The Advanced menus provide additional options for the UPS and are available only if

the display interface is configured to use the Advanced menus.

Menu General Functions

Status View detailed UPS information:

• Operating Mode

• Efficiency

• Load Power

• Load VA

• Load Amps

• Load Energy

• Battery Charge State

• Estimated Runtime

• Battery Voltage

•Battery Temp

• Input

• Output

• Outlet Groups

• SmartConnect

• Probe 1, Probe 2, when NMC

and sensor probes are

installed

Control Controls the Main and Controlled Outlet Group to turn on, turn off,

shutdown, or reboot:

• UPS Control

• Outlet Group Control

Configuration Configure advanced UPS

settings:

• Language

• Output Voltage

Note: Setting can be

configured only when UPS

output is turned off.

• Green Mode

• Local Power Quality

• Menu Type

• Audible Alarm

• Display

• Sensitivity

• Low Transfer

• High Transfer

• Low Battery Setting

• Auto Self Test

• Reset Energy Meter

• Enter Setup Wizard

• Reset to Factory Defaults

• Site Wiring Fault

• Config Main Group Outlets

• Config Group Outlets (if

Controlled Outlet is available)

• ModBus Settings

• SmartConnect Control

• UPS IP Address Setting

• NMC IP Address Settings (if

NMC is available)

• FW Update Interfaces

• Install FW? (only available if a

firmware update is available)

Test & Diag Perform UPS tests and

diagnostics functions:

• UPS Self Test

•UPS Alarms Test

Logs View the error log for information about UPS errors that have

occurred.

Operation

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

EN TME20822 – 08/2023

About View UPS information:

• UPS Model

• UPS Part No.

• UPS Serial No.

• UPS Manufacture Date

• Battery Part No.

• Battery Install Date

• Replace Battery by

• Running UPS FW

• Available UPS FW

Note: Enabled only if a UPS

firmware update is available.

• UPS MAC

• UPS IP Address

• UPS Product Key

• SmartSlot Card (if installed)

Menu General Functions

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

Configuration

EN TME20822 – 08/2023

Configuration

General configuration settings

Configuration settings may be changed at any time using the LCD interface or

PowerChute software. This table provides a brief description of the general settings,

for more detailed information on each of these parameters consult application note 80

at www.apc.com.

Setting

Factory

Default

Options Description

High Transfer 253 Vac 253 Vac - 265 Vac To avoid unnecessary battery usage, set the

transfer point higher if the AC voltage is

chronically high and the connected equipment is

known to work under this condition. The Power

Quality setting will automatically change this

setting.

NOTE: Use the Advanced Menus to configure

this setting.

Low Transfer 207 Vac 195 Vac - 207 Vac Sets the transfer point lower if the AC voltage is

chronically low and the connected equipment can

tolerate this condition. This setting may also be

adjusted using the power quality setting.

NOTE: Use the Advanced Menus to configure

this setting.

Sensitivity Normal • Normal

• Reduced

•Low

Selects the level of sensitivity to power events

that the UPS will tolerate.

• Normal: The UPS will go on battery power more

often to provide the cleanest power supply to

the connected equipment.

• Low: The UPS will tolerate more fluctuations in

power and will go on battery power less often.

If the connected load is sensitive to power

disturbances, set the sensitivity to Normal.

Date of Last

Battery

Replacement

Date set at factory. Reset this date when the battery module is replaced.

Display Auto Off • Auto Off

• Auto Dim

•Always On

The UPS can be configured to change the LCD

brightness when the interface has not been used

for 4 minutes.

• Auto Off: The LCD turns off. This is used as the

default to extend LCD lifetime.

• Auto Dim: The LCD switches to a lower

brightness.

• Always On: The LCD is always at the lower

brightness and does not change due to

inactivity.

Audible Alarm On • On

•Off

The UPS will mute all audible alarms if this is set

to Off or when the display buttons are pressed.