SU_UM_TME20822_EN.pdf - 第23页

23 Confi guration Smart-UPS SMTL 220 0/3000 RMI2UC/RMI2UCNC EN T ME2 0822 – 08 /202 3 Ou tle t grou p con fig ura tio n se tti ngs The Main Outlet Group and the C ont rolled Outlet Group c an be config ured to independen…

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

Configuration

EN TME20822 – 08/2023

Configuration

General configuration settings

Configuration settings may be changed at any time using the LCD interface or

PowerChute software. This table provides a brief description of the general settings,

for more detailed information on each of these parameters consult application note 80

at www.apc.com.

Setting

Factory

Default

Options Description

High Transfer 253 Vac 253 Vac - 265 Vac To avoid unnecessary battery usage, set the

transfer point higher if the AC voltage is

chronically high and the connected equipment is

known to work under this condition. The Power

Quality setting will automatically change this

setting.

NOTE: Use the Advanced Menus to configure

this setting.

Low Transfer 207 Vac 195 Vac - 207 Vac Sets the transfer point lower if the AC voltage is

chronically low and the connected equipment can

tolerate this condition. This setting may also be

adjusted using the power quality setting.

NOTE: Use the Advanced Menus to configure

this setting.

Sensitivity Normal • Normal

• Reduced

•Low

Selects the level of sensitivity to power events

that the UPS will tolerate.

• Normal: The UPS will go on battery power more

often to provide the cleanest power supply to

the connected equipment.

• Low: The UPS will tolerate more fluctuations in

power and will go on battery power less often.

If the connected load is sensitive to power

disturbances, set the sensitivity to Normal.

Date of Last

Battery

Replacement

Date set at factory. Reset this date when the battery module is replaced.

Display Auto Off • Auto Off

• Auto Dim

•Always On

The UPS can be configured to change the LCD

brightness when the interface has not been used

for 4 minutes.

• Auto Off: The LCD turns off. This is used as the

default to extend LCD lifetime.

• Auto Dim: The LCD switches to a lower

brightness.

• Always On: The LCD is always at the lower

brightness and does not change due to

inactivity.

Audible Alarm On • On

•Off

The UPS will mute all audible alarms if this is set

to Off or when the display buttons are pressed.

Configuration

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

EN TME20822 – 08/2023

Outlet group configuration settings

The Main Outlet Group and the Controlled Outlet Group can be configured to

independently turn off, turn on, shut down, and reboot connected equipment.

The Main and Controlled Outlet Groups can be configured to do the following:

• Turn OFF: Disconnect from power immediately and restart only with a manual

command.

• Turn ON: Connect to power immediately.

• Shutdown: Disconnect power in sequence, and automatically reapply power in

sequence when AC power becomes available.

• Reboot: Shut down and restart.

Auto Self Test On start-up

and every 14

days since the

last test

• Never

• Start-up only

• Frequency of test (every 7 to

14 days)

The interval at which the UPS will execute a self-

test.

Reset to

Factory

Default

No Yes/No Restores the UPS factory default settings.

Site Wiring

Fault

Enable Enable/Disable/

Can Ack

Sets the Site Wiring Fault detection to Enable,

Disable or User Can Acknowledge

Output voltage 230 V • 220Vac

• 230Vac

• 240Vac

Selects the output voltage. This is only settable

when the UPS is turned off.

Select the output voltage appropriate to the

location.

Green Mode Enable • Enable

• Disable

This will enable or disable Green mode function.

Green Mode conserves energy while the UPS is

operating on line.

SmartConnect

Control

Enable • Enable

• Disable

This will permit remote configuration changes.

Low Battery

Setting

150 sec Set the value in seconds The UPS will emit an audible alarm when the

remaining runtime has reached this level.

FW Update

Interfaces

Enable • Enable

• Disable

Enable or disable FW updates.

• Serial port

• SmartConnect Ethernet port

•SmartSlot

•USB

Communication port through which the FW is to

be updated.

NOTE: This option will get enabled only when

FW Update Interfaces is set to Enable.

Install FW? Don’t Install • Next off (Updates the UPS

Firmware next time that the

UPS is turned off)

• Now (Updates the UPS

firmware immediately

without interrupting

operations)

•Don't Install

Firmware update: this only appears when new

firmware is available in the flash memory of the

UPS and is ready to be installed

Setting

Factory

Default

Options Description

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

Configuration

EN TME20822 – 08/2023

In addition, the Main Outlet Group and the Controlled Outlet Group can be configured

to do the following:

• Turn ON or Turn OFF in a specified sequence

• Automatically turn OFF or shut down when various conditions occur

NOTE: If the Main and Controlled Outlet Groups are not configured, all the outlets on

the unit will still provide battery back-up power.

NOTE: The Main Outlet Group functions as a master switch. It will turn on first when

power is applied, and shut off last when there is a power outage and battery run-time

has been exhausted.

The Main Outlet Group must be turned on for the Controlled Outlet Group to turn on.

Setting Factory Default Options Description

Name String

Outlet Group

Outlet Group 1 Edit these names using an external interface, such as the Network

Management Card Web interface.

UPS Name

String

UPS Outlets

Turn On Delay 0 sec Set the value in

seconds

The amount of time the UPS or the Controlled Outlet

Group will wait between receiving the command to turn on

and the actual startup.

Turn Off Delay • 0 sec (UPS

Outlets)

• 90 sec

(Controlled

Outlet Groups)

Set the value in

seconds

The amount of time the UPS or the Controlled Outlet

Group will wait between receiving the command to turn off

and the actual shut down.

Reboot

Duration

8 sec Set the value in

seconds

The amount of time that the UPS or the Controlled Outlet

Group must remain off before it will restart.

Minimum

Return Time

0 sec Set the value in

seconds

The amount of battery runtime that must be available

before the UPS or the Controlled Outlet Group will turn

on.

Load Shed On

Battery

Disabled • Shutdown with

Delay

• Shutdown

immediately

• Turn off

immediately

• Turn off with

delay

• Disabled

When the unit switches to battery power, the UPS can

disconnect power to the Controlled Outlet Group to save

runtime.

To configure this delay time, use the L

OAD SHED TIME

WHEN ON BATTERY setting.

Load Shed

Time when On

Battery

Disabled Set the value in

seconds

The amount of time the outlets will function on battery

power before they will turn off.