SU_UM_TME20822_EN.pdf - 第24页

24 Smart-UPS S MTL 22 00/3000 RMI2UC/RMI2UCNC Config uration EN TME2 08 22 – 08/2 023 In add it ion, t he Main O utlet Grou p and the Controlled O ut let Group can be conf igured to do the following: • T urn ON or T urn …

Configuration

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

EN TME20822 – 08/2023

Outlet group configuration settings

The Main Outlet Group and the Controlled Outlet Group can be configured to

independently turn off, turn on, shut down, and reboot connected equipment.

The Main and Controlled Outlet Groups can be configured to do the following:

• Turn OFF: Disconnect from power immediately and restart only with a manual

command.

• Turn ON: Connect to power immediately.

• Shutdown: Disconnect power in sequence, and automatically reapply power in

sequence when AC power becomes available.

• Reboot: Shut down and restart.

Auto Self Test On start-up

and every 14

days since the

last test

• Never

• Start-up only

• Frequency of test (every 7 to

14 days)

The interval at which the UPS will execute a self-

test.

Reset to

Factory

Default

No Yes/No Restores the UPS factory default settings.

Site Wiring

Fault

Enable Enable/Disable/

Can Ack

Sets the Site Wiring Fault detection to Enable,

Disable or User Can Acknowledge

Output voltage 230 V • 220Vac

• 230Vac

• 240Vac

Selects the output voltage. This is only settable

when the UPS is turned off.

Select the output voltage appropriate to the

location.

Green Mode Enable • Enable

• Disable

This will enable or disable Green mode function.

Green Mode conserves energy while the UPS is

operating on line.

SmartConnect

Control

Enable • Enable

• Disable

This will permit remote configuration changes.

Low Battery

Setting

150 sec Set the value in seconds The UPS will emit an audible alarm when the

remaining runtime has reached this level.

FW Update

Interfaces

Enable • Enable

• Disable

Enable or disable FW updates.

• Serial port

• SmartConnect Ethernet port

•SmartSlot

•USB

Communication port through which the FW is to

be updated.

NOTE: This option will get enabled only when

FW Update Interfaces is set to Enable.

Install FW? Don’t Install • Next off (Updates the UPS

Firmware next time that the

UPS is turned off)

• Now (Updates the UPS

firmware immediately

without interrupting

operations)

•Don't Install

Firmware update: this only appears when new

firmware is available in the flash memory of the

UPS and is ready to be installed

Setting

Factory

Default

Options Description

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

Configuration

EN TME20822 – 08/2023

In addition, the Main Outlet Group and the Controlled Outlet Group can be configured

to do the following:

• Turn ON or Turn OFF in a specified sequence

• Automatically turn OFF or shut down when various conditions occur

NOTE: If the Main and Controlled Outlet Groups are not configured, all the outlets on

the unit will still provide battery back-up power.

NOTE: The Main Outlet Group functions as a master switch. It will turn on first when

power is applied, and shut off last when there is a power outage and battery run-time

has been exhausted.

The Main Outlet Group must be turned on for the Controlled Outlet Group to turn on.

Setting Factory Default Options Description

Name String

Outlet Group

Outlet Group 1 Edit these names using an external interface, such as the Network

Management Card Web interface.

UPS Name

String

UPS Outlets

Turn On Delay 0 sec Set the value in

seconds

The amount of time the UPS or the Controlled Outlet

Group will wait between receiving the command to turn on

and the actual startup.

Turn Off Delay • 0 sec (UPS

Outlets)

• 90 sec

(Controlled

Outlet Groups)

Set the value in

seconds

The amount of time the UPS or the Controlled Outlet

Group will wait between receiving the command to turn off

and the actual shut down.

Reboot

Duration

8 sec Set the value in

seconds

The amount of time that the UPS or the Controlled Outlet

Group must remain off before it will restart.

Minimum

Return Time

0 sec Set the value in

seconds

The amount of battery runtime that must be available

before the UPS or the Controlled Outlet Group will turn

on.

Load Shed On

Battery

Disabled • Shutdown with

Delay

• Shutdown

immediately

• Turn off

immediately

• Turn off with

delay

• Disabled

When the unit switches to battery power, the UPS can

disconnect power to the Controlled Outlet Group to save

runtime.

To configure this delay time, use the L

OAD SHED TIME

WHEN ON BATTERY setting.

Load Shed

Time when On

Battery

Disabled Set the value in

seconds

The amount of time the outlets will function on battery

power before they will turn off.

Configuration

Smart-UPS SMTL 2200/3000 RMI2UC/RMI2UCNC

EN TME20822 – 08/2023

Modbus settings

Load Shed On

Runtime

Disabled • Shutdown with

delay

• Shutdown

immediately

• Turn off

immediately

• Turn off with

delay

• Disabled

When the battery runtime falls below the specified value,

the Controlled Outlet Group will turn off.

Configure this time using the L

OAD SHED RUNTIME

EMAINING setting.

Load Shed On

Runtime

Remaining

Disabled Set the value in

seconds

When the remaining runtime reaches this level, the

Controlled Outlet Group will turn off.

Load Shed on

Overload

Disabled • Disabled

• Enabled

In the event of an overload (greater than 100% output

power), the Controlled Outlet Group will immediately turn

off to conserve power for critical loads. The Controlled

Outlet Group will only turn on again with a manual

command.

Setting Factory Default Options Description

Slave ID 1 1- 223 Sets the Modbus slave address of UPS

Ser+USB Disable • Enable

• Disable

Enables or disables UPS Modbus protocol over serial and

USB ports

TCP Settings

TCP

Protocols

Disable • Disable

• Read-Only

• Read-Write

Enables or disables UPS Modbus TCP/IP protocol

provided by the embedded SmartConnect port.

• Disable: Disables UPS Modbus TCP/IP protocol

• Read-Only: Modbus master over TCP/IP protocol is only

allowed to get UPS status.

• Read-Write: Modbus master over TCP/IP protocol is

allowed to get UPS status and control the UPS.

The port number of UPS Modbus TCP/IP protocol is fixed

at 502.

Master IP

Addr

000.000.000.000 A valid IPv4

address

Specifies the IPv4 address of the Modbus master that will

allow connection to the UPS via Modbus TCP/IP protocol

The Master IP Addr when set as 000.000.000.000 will allow

connection of external Modbus master with any IP address.

When not set as 000.000.000.000, only the Modbus master

with the specified IP address is allowed to connect to the

UPS.

Example: Master IP Address is set to 192.168.0.10, only

Modbus master with IP address 192.168.0.10 could

connect to the UPS.

Setting Factory Default Options Description