00195779-0102_UM_D4_SR605_EN - 第218页
5 Tasks for the operating personnel User manual SIPLACE D4 5.10 Docking the component trolley in or out From software version SR.605.xx 07/2008 EN Edition 218 5 Fig. 5.10 - 2 Component trolley - swivel handles up to push…
User manual SIPLACE D4 5 Tasks for the operating personnel
From software version SR.605.xx 07/2008 EN Edition 5.10 Docking the component trolley in or out
217
Fig. 5.10 - 1 Docking the component trolley in or out
5
(1) Button for raising the component table bed (beneath the cover flap)
(2) Plug for connecting the component trolley cable
(3) Component table bed, can be raised or lowered
(4) Button for lowering the component table bed
(5) CO trolley handle
(6) Centering hole for the centering pins
(7) Supporting surface for the component table bed (right and left)
(8) Centering pin for the component table bed
5 Tasks for the operating personnel User manual SIPLACE D4
5.10 Docking the component trolley in or out From software version SR.605.xx 07/2008 EN Edition
218
5
Fig. 5.10 - 2 Component trolley - swivel handles up to push
5
(1) Handle
(2) Button for lowering the component table
→ With both hands on the handles, pull the component trolley out of the machine.
→ Turn the switch on the component table (item 4 in Fig. 5.10 - 2
) down. The component table
is lowered.
WARNING 5
→ Please follow the safety instructions for moving the component trolley described in Section
2.5.4, page 53.
User manual SIPLACE D4 5 Tasks for the operating personnel
From software version SR.605.xx 07/2008 EN Edition 5.10 Docking the component trolley in or out
219
5.10.2 Docking in the component trolley
PLEASE NOTE 5
Shorten the component tapes on the front end of the S feeder modules to approximately 1 cm
before you dock in the component trolley.
CAUTION 5
Check that the placement head is outside the range of the component trolley.
→ Make sure that the left and right contact surfaces (item 7 in Fig. 5.10 - 1
, page 217) for the
component table bed is clean.
→ Check that the contact surfaces on the underside of the component table bed are clean.
→ CAREFULLY push the component trolley into the machine.
→ Plug the connecting cable of the component trolley into the socket (item 2 in Fig. 5.10 - 1
,
page 217
) on the machine.
→ Open the cover over the push-button used to raise and lower the component table bed (item
1 in Fig. 5.10 - 1
, page 217).
→ Turn the switch on the component table (item 4 in Fig. 5.10 - 1
, page 217) down.
→ Press the button until the component table bed has reached the upper final position.
→ Carefully push the component trolley into machine as far as the stop.
→ Check that the centering holes in the component table bed lie precisely over the centering
pins of the machine (item 8 in Fig. 5.10 - 1
, page 217).
WARNING DANGER OF CRUSHING 5
When lowering the component table bed, never reach into the gap between the feeders and
the used tape channel. 5
→ Press the button for lowering the component table bed (item 4 in Fig. 5.10 - 1
, page 217).
→ Ensure that the centering pins engage in the centering holes in the component table bed and
that the component table bed is fully lowered.
→ Close the cover over the push-button (item 1 in Fig. 5.10 - 1
, page 217).
→ Close the protective cover.