5OM-1626-001_w - 第24页

Safety Precautions Safe-13 1OM-1610 Alert Indications described as " " (continuted) Alert Description Related Items This setup operat ion must be performed with your hands inserted inside the machine. Open the …

100%1 / 213
Safety Precautions
Safe-12
1OM-1610
Alert Indications described as " " (continuted)
Alert Description Related Items
When a tape feeder is attached or detached, be sure not to
drop it.
Otherwise, a foot injury will result or the feeder itself may be
damaged.
Carefully handle each feeder one by one and do not drop any.
"3.8" in
"Chapter 1 (Vol. 1)"
"2.1" in
"Chapter 3 (Vol. 1)"
"2.4" in
"Chapter 4 (Vol. 1)"
Hazardoustoyourhands
andngers!
·
Be sure to hold the handle to move the bank feeder change cart.
"3.8.1" in
"Chapter 1 (Vol. 1)"
"2.4" in
"Chapter 4 (Vol. 1)"
Watchyourstep!
·
Be careful not to hit your foot against the cart while moving the bank
feeder change cart.
Especially, the resistance against cart movement may change rapidly
when the oor is ragged and the cart gets caught on the oor or
a sheet is used and the cart gets caught at the edge or a slackened
portion of the sheet.
·
Be sure to insert the feeder deep inside.
When the tape feeder is mounted onto the feeder carriage, make sure
that it has been inserted to the rear end and xed securely
.
If not, the tape feeder might drop, which might result in an injury on
your foot or damage to the feeder.
"3.8.1" in
"Ch
apter 1 (Vol. 1)"
"2.4" in
"Chapter 4 (Vol. 1)"
Do not put your hand in the moving area while the feeder base is
moving up or down.
While the LED of a [FEEDER READY] switch is being ickering, it
indicates that the corresponding feeder base is moving up and down.
"2.4.8" in
"Chapter 1 (Vol. 1)"
The padlock key should be kept in such a way that nobody except the
personnel in charge of maintenance can supervise it.
"4.3" in
"Chapter 2 (Vol. 1)"
The load power to the motors, etc., is turned OFF but the
maintenance operation must be performed carefully, protecting
your hands from any injury.
"3.3.1." and
"3.3.2" and
"3.4" in
"Chapter 4 (Vol. 1)"
0911-001
CAUTION
3. Alert Indications in Instruction Manual
Safety Precautions
Safe-13
1OM-1610
Alert Indications described as " " (continuted)
Alert Description Related Items
This setup operation must be performed with your hands inserted
inside the machine.
Open the transparent cover(door type) and perform the setup
operation with the load power supply to the servomotor being
turned "OFF".
"5.1.2" in
"Chapter 4 (Vol. 2)"
In this teaching operation, the cover of the light source device
need not be opened.
Do not open the cover of the light source device.
The cover of the light source device, when opened, exposes users to the
high voltage components and may result in electrical shocks.
"6.5.15" in
"Chapter 4 (Vol. 2)"
Be sure to wear gloves during cleaning. Otherwise, you may cut your
hands on the edges of the lighting hood.
"3.3.3" in
"Chapter 1 (Vol. 4)"
•
Even when the power breaker is set to "OFF", the primary line
is powered, making it possible to cause an electric shock.
Be sure to completely stop the power supply to the machine before
maintenance work.
"1.1" in
"Chapter 1 (Vol. 4)"
•
Residual voltages may remain behind for a few minutes in the
internal devices of the machine after power interception.
Before performing maintenance work, wait until the charge lamps of
the DC power supply and the servoamplier go "OFF" in 10 minutes
or more after the power breaker is set to "OFF".
"1.1" in
"Chapter 1 (Vol. 4)"
When
theatring
iscut,takecarenottogetinjuredbythe
commercially available cutter.
"3.3.6" in
"Chapter 1 (Vol. 4)"
Your hand might be cut at the edge of the linear guide in the
cleaning operaiton. Wear gloves.
"3.3.8" in
"Chapter 1 (Vol. 4)"
The light emitter of the linear measure sensor is made of glass.
If the light emitter happens to be damaged, be sure to suck up
the fragments with a vacuum cleaner, etc.
Do not collect the fragments with your bare hands to protect your
hands from injuries.
"4.5" in
"Chapter 1 (Vol. 4)"
CAUTION
0911-001
3. Alert Indications in Instruction Manual
Safety Precautions
Safe-14
1OM-1610
4. Alert Labels
The alert labels (described below) are used for this machine.
Please read the instructions on each label carefully and check the contents, observing the
actual object.
Be sure to follow the instructions for safety purposes.
These labels should be kept clean and easily legible at a far safe distance.
When a label has deteriorated and become illegible, contact our service department for
the replacement with a new one.
0911-001
4. Alert Labels