YSI_Prog_E - 第26页

General Contents Before using the machine 1. Using this manual i 1.1 A vailable manuals i   i 2. W arranty i i 3. Contents of each chapter ii i 4. Page layout i v Chapter 1 Basic operation   …

xxiii

Safety instructions

3.4 Label positions

Warning/caution labels are attached to the YAMAHA products to ensure safe and correct use. Check that the

information on each label is clearly legible and comply with the instructions.

For safety precautions other than those on the labels shown in this section, see the instructions in "1. Safety".

NOTE

When connecting power to this equipment, refer to "Power connection terminals" described in the appendix of the

operator's manual.

NOTE

The label contents and positions are slightly differ depending on machine model. For the label contents and positions,

refer to the operator's manual for the machine being used.

General Contents

Before using the machine

1. Using this manual i

1.1 Available manuals i

  i

2. Warranty ii

3. Contents of each chapter iii

4. Page layout iv

Chapter 1 Basic operation

   1

  1

  2

1.3 Setup screen 1-3

  4

1.4.1 "Board" screen 1-4

1.4.2 "Fiducial" screen 1-5

1.4.3 "Bad Mark" screen 1-6

1.4.4 "View" screen 1-7

1.4.5 "Step" screen 1-8

1.4.6 "Height Correct" screen (YSi-X) 1-11

1.4.7 "Code Scan" screen 1-12

1.5 Auto inspection screen 1-13

1.5.1 "Inspection" screen 1-13

1.5.2 "Whole" screen 1-14

1.5.3 "Output" screen 1-15

1.5.4 "Bad Mark" screen 1-16

1.5.5 "Judge" screen 1-16

1.5.6 "Height Measure" screen 1-17

1.5.7 "Conveyor" screen 1-18

1.5.8 "Carry Log" screen 1-19

  0

1.6.1 "Conveyor" screen 1-20

1.6.2 "I/O" screen 1-22

1.7 History 1-24

1.8  5

2. Starting and ending inspection 1-26

2.1 Starting automatic inspection 1-26

2.1.1 Selecting inspection programs 1-26

2.1.2 Starting automatic inspection 1-27

  8

2.2.1 Selecting inspection programs 1-28

EPP

100

2.2.2 Starting automatic inspection 1-29

2.2.3 Upside down automatic inspection settings 1-30

2.3 When NG detection occurs 1-32

2.3.1 NG monitor 1-32

2.4 Inspection complete screen 1-34

2.5 Ending the automatic inspection 1-35

Chapter 2 Creating inspection programs

   1

  1

1.2 Inspection method 2-2

1.2.1 Optical inspection 2-2

1.2.2 X-ray inspection 2-4

  5

1.3.1 Inspection with optical camera 2-5

1.3.2 Inspection with X-ray camera 2-8

2. Creating inspection programs 2-9

  9

  0

2.3 Creating full board images 2-12

  5

2.4.1 Basic parameters 2-16

2.4.2 Fiducial mark settings 2-18

2.4.3 Setting fiducial mark CUSTOM lighting 2-22

2.5  4

2.5.1 Basic parameters 2-25

2.5.2 Bad mark settings 2-26

  9

2.6.1 Saving view images 2-29

2.6.2 Using view images 2-30

2.6.3 Creating all views and shortening inspection time 2-31

2.6.4 Manual view creation procedure 2-32

2.6.5 Multiple view operations 2-34

2.7 Step settings 2-38

2.7.1 Pasting libraries 2-38

2.7.2 Step creation procedure 2-40

2.7.3 Registering libraries 2-44

2.7.4 Deploying libraries 2-46

2.7.5 Checking libraries 2-48

2.7.6 Saving view images 2-49

2.8 Library details 2-50

Chapter 3 Step screen

1. Parameters 3-1

  1