00195722-0102_UM_X-Serie_SR605_EN - 第317页
User Manual SIPLACE X-Series 4 Setting up and commissioning From software version SR.605.xx 07/2008 EN Edition 4.6 Adapting th e used tape channel 317 4 Fig. 4.6 - 2 Used tape channel with component reject bin (1) Separa…
4 Setting up and commissioning User Manual SIPLACE X-Series
4.6 Adapting the used tape channel From software version SR.605.xx 07/2008 EN Edition
316
4.6.1.1 Safety instructions
WARNING 4
→ Switch the placement machine off at the main switch to remove the dividing plate.
→ Disconnect the machine from the power and compressed air supply.
→ Secure the machine to prevent it being switched on again, as described in Section 2.10
, page
96
.
→ Wait until the operating pressure for the tape cutter has dropped to 0 MPa.
→ Do not reach inside the used tape channel.
4.6.1.2 Removing the separating plate
→ Loosen the two hexagon head screws (item 2 in Fig. 4.6 - 1, page 315).
→ Pull out the separating plate (item 1 in Fig. 4.6 - 1
, page 315).
4.6.2 Adapting the SIPLACE HF used tape channel to the component height
If S feeder modules that process component tapes with a pocket height > 17 mm are used, such
as, for example, the 44 mm S DP feeder module, then the separating plate (item 1 in Fig. 4.6 - 2
,
page 317
) must be removed.
4.6.2.1 Safety instructions
WARNING 4
→ Switch the placement machine off at the main switch to remove the dividing plate.
→ Disconnect the machine from the power and compressed air supply.
→ Secure the machine to prevent it being switched on again, as described in Section 2.10
, page
96
.
→ Wait until the operating pressure for the tape cutter has dropped to 0 MPa.
→ Wear robust protective gloves.
→ Do not reach inside the used tape channel.
User Manual SIPLACE X-Series 4 Setting up and commissioning
From software version SR.605.xx 07/2008 EN Edition 4.6 Adapting the used tape channel
317
4
Fig. 4.6 - 2 Used tape channel with component reject bin
(1) Separating plate for tapes > 17 mm, removable
(2) DIN 84 - M3x6 screw, 2x
4
4
4.6.2.2 Removing the separating plate
→ Loosen the two slotted screws (item 2 in Fig. 4.6 - 2).
→ Pull out the separating plate (item 1 in Fig. 4.6 - 2
).
4 Setting up and commissioning User Manual SIPLACE X-Series
4.7 Commissioning the machine From software version SR.605.xx 07/2008 EN Edition
318
4.7 Commissioning the machine
4.7.1 Commissioning the machine at the customer's premises
→ Check all modules for correct seating.
→ Wipe off the linear guide rails with a lint-free cloth before removing the shipping braces for the
X/Y axis. Do not use any solvent to do this (see Section 4.3.19
, page 307.
→ Switch on the machine and perform a reference run.
→ Copy the placement program onto the computer and test it.
→ Check the machine zero point after a period of warming up of 3 - 4 h.
→ Get the customer's operating personnel to equip the feeder modules according to the cus-
tomer's placement program.
→ Instruct them in handling the feeder modules using the JobGuide.
→ Check all customer-specific installed options (in particular software) for good functioning and
order any necessary spare parts using the order form or by fax.
4.7.2 Instructing the customer's personnel
→ Explain all customer-specific installed options, in particular software / software compatibility.
→ Explain programming of the program editors on the line computer / SIPLACE Pro.
→ Instruct the operators and line engineers in using the station software.
→ Explain about password protection.
→ Instruct the customer's personnel according to the user manual and the preventive mainte-
nance.
4.7.3 A test run or starting production
→ Test the line using the test PCB or a PCB provided by the customer.
→ Record the customer product and performance data, prepare the data and document the data
in the installation report.
→ Secure the data and give the customer security copies.