00193922-03 - 第136页
3 Technical data User manual SIPLACE HF series 3.9 Controls Software Vers ion SR.50x.xx 01/2006 US Edition 136 Component barcode scanner 3 On each sid e of the middle co nsole there is a bracket that holds the Datalogic …
User manual SIPLACE HF series 3 Technical data
Software Version SR.50x.xx 01/2006 US Edition 3.9 Controls
135
3.9.2 Description
All the controls can be reached by a 1.60 m tall person. 3
Main power switch 3
The main power switch is used to switch the power supply to the placement machine on and off.3
WARNING
Some parts inside the placement machine carry potentially lethal voltages - even when switched
off at the main power switch. 3
Stop button 3
This button is used to stop the placement machine. 3
Start button 3
This button starts the placement machine after it has been switched on or after faults have been
eliminated. 3
Emergency stop button 3
The emergency stop button latches in the ON position when pressed. The power supply to the
gantry axes, the component trolleys, conveyors and used tape cutters is interrupted and the volt-
age supplied to the star axes of the placement heads is reduced. Turn the button to release it. 3
Component counter 3
The component counter displays the number of components processed. 3
LCD touchscreen 3
There is a flat LCD screen with a touch-sensitive surface (touchscreen) on either side of the
placement machine. 3
Keyboard 3
The keyboard is located beneath the monitor. 3
Indicator lamp 3
The sequence of colors is white - green - white. These lamps are used to signal operating sta-
tuses and malfunctions of the placement machine. 3
3 Technical data User manual SIPLACE HF series
3.9 Controls Software Version SR.50x.xx 01/2006 US Edition
136
Component barcode scanner 3
On each side of the middle console there is a bracket that holds the Datalogic DL 910 component
barcode scanner. The barcode scanner enables the components to be set up and topped up
quickly and reliably. 3
3
3
3.9.3 Ergonomic arrangement of the controls
Figure 3.9 - 1 on page 134 provides an overview of the position of the controls. They are subdi-
vided into the following groups: 3
Operator panel on the right-hand side (pneumatic unit) of the center console with 3
– LCD touchscreen
– Keyboard with trackball
– Start button, Stop button
Operator panel on the left-hand side (power supply unit) of the center console with 3
– LCD touchscreen
– Keyboard with trackball
– Component counter
– Start button
– Stop button
– Main power switch
Input / output side of the PCB conveyor with 3
– Emergency stop buttons
– Start button, Stop button
– Button for docking and undocking the component trolley
User manual SIPLACE HF series 3 Technical data
Software Version SR.50x.xx 01/2006 US Edition 3.9 Controls
137
3.9.3.1 Controls on the placement machine's operator panels
The two operator panel have identical control functions. 3
Monitor, keyboard, Start and Stop buttons 3
There is a monitor and a keyboard on both sides of the placement machine. 3
The Start and Stop buttons are located beneath the keyboard. The on-screen dialog will occa-
sionally prompt you to activate certain actions using buttons, and this arrangement will make it
easier for you both to activate and to interactively control these actions. 3
Main power switch 3
The main power switch is part of the power module. It is located on the left-hand operator panel
viewed in the direction of PCB transport. It is located here because it is only needed for servicing
and preventive maintenance work and is therefore not subject to frequent use. 3
3
3
3.9.3.2 Controls on the input and output sides of the placement machine
The controls on the input and output sides of the placement machine perform identical functions.3
Emergency stop buttons, Start and Stop buttons 3
There is an emergency stop button and two Start and Stop buttons on both the input and output
sides of the PCB conveyor. This arrangement was adopted for the emergency stop buttons be-
cause it enables them to be reached quickly and easily from any position. 3
In addition, it is important to have an unrestricted view of the placement heads and placement
area during preventive maintenance, servicing and setting up work in order to be able to check
all the operations carried out inside the machine. This particularly important during testing
phases or when starting single functions, for example. 3