SECS GEM Manual - 第144页
GEM Manual for DEK Printers Event M essages Issue 1.6 January 22, 2018 Page 144 of 171 31220 Print pressure error. 31221 File error. 31222 Unable to recover . 31223 Recovery started. 31224 Recovered. 31225 Upline transfe…
GEM Manual for DEK Printers Event Messages
Issue 1.6 January 22, 2018 Page 143 of 171
8.5 Acknowledge Terminal Message Event
EVENT - CEID
DESCRIPTION
31441 Acknowledge terminal message.
8.6 Alarm Events
EVENT - CEID
DESCRIPTION
31253 Cover opened.
31254 Cover closed.
31314 Head left partly open.
31315 Head moved to safe state.
8.7 Spooling Events
EVENT - CEID
DESCRIPTION
31453 Spooling activated.
31454 Spooling deactivated.
31455 Spool transmission failure.
8.8 Equipment Error Events
EVENT - CEID
DESCRIPTION
10003 System power down.
31201 Pneumatic power down.
31202 Front squeegee error.
31203 Rear squeegee error.
31204 Rising table error.
31205 Print carriage error.
31206 Paste carriage error.
31207 Camera X axis error.
31208 Camera Y axis error.
31209 Rail width error.
31210 Screen XF error.
31211 Screen XR error.
31212 Screen Y error.
31213 Paste cartridge tilt error.
31214 Screen changer drive error.
31215 Board stop stuck.
31216 Board clamp stuck.
31217 Board stuck in rails.
31218 Unable to find fiducial.
31219 Rail lifted error.
GEM Manual for DEK Printers Event Messages
Issue 1.6 January 22, 2018 Page 144 of 171
31220 Print pressure error.
31221 File error.
31222 Unable to recover.
31223 Recovery started.
31224 Recovered.
31225 Upline transfer error.
31226 Downline transfer error.
31227 Dual shuttle fault.
31230 Screen changer fault.
31232 Lid bolt fault.
31233 Alignment out of range.
31417 Comms error.
31303 Barcode read failure.
31304 Barcode mismatch.
31305 Screen couplings failed.
31306 Motion control timeout.
31307 Camera X failed to position.
31308 Camera Y failed to position.
31309 Stencil aperture blocked.
31310 Stencil smeared.
31311 Paste on pad inspection error.
31312 Bridging detected by inspection system.
31313 Alignment error detected by inspection system.
31321 Event log disk file full.
31322 Proflow error.
31340 CAN node down.
31341 CAN node recovered.
31342 CAN bus down.
31343 CAN bus comms restored.
31344 Invalid CAN response.
31433 CAN bus recovered.
31460 Volume alarm.
40006 Dongle error.
40028 Roll Height Monitor failed.
40043 Knead pressure error (front).
40044 Knead pressure error (rear).
40045 Print pressure error (front).
40046 Print pressure error (rear).
40047 Servo following error.
40048 Board fiducial 1 not found.
40049 Board fiducial 2 not found.
GEM Manual for DEK Printers Event Messages
Issue 1.6 January 22, 2018 Page 145 of 171
40050 Board fiducial 3 not found.
40051 Screen fiducial 1 not found.
40052 Screen fiducial 2 not found.
40053 Screen fiducial 3 not found.
40054 Select mark not found.
40056 Bad tooling vacuum.
40146 Cleaner detached from camera.
40147 Recovered cleaner detached from camera.
40148 Method of post print analysis is not enabled.
40149 Producing without post print analysis.
40150 Ball escape detected.
40152 Verification item failed (see DVID 2034).
40157 Product ID verification failed.
40300 Advanced Adjust Entered.
40320 Cleaner Vacuum Sense Error.