MPM全自动印刷机中文操作手册 - 第28页
28 The FRAME CLAMPS will activate when ( 按 NEXT 後 , 啟動鎖住鋼板 ) you press NEXT . Pr ess NEXT to Continue, or EXIT to Quit. ( 按 NEXT 繼續 , 按 EXIT 離開 ) 你按 NEXT 之後，出現下列訊息及視窗： The next step is to set STENCIL HEIGHT . ( 然後進行測鋼板高度…
27
Jog to the same target on the stencil!(請移動到鋼板上任一個對位 Mark 點
Center the object. Press EXIT ，對正 Mark 中心點，但必須與基板上
Mark 點一樣,按 EXIT 離開)
※但如果 X 軸方向,超過軟體保護極限會出現下列訊息,可能需重做對位點。
1.3.3 選擇 Calc. Pre-Boardstops-X 進入基板 X 方向停止位置參數設定
Pre board stop position learned (機器自行計算基板停止位置)
Press SELECT to continue(按 SELECT 繼續)
Press Done when finished. (當你做完上述之步驟，按 Done)
1.4 選擇 Stencil 進入測鋼板高度參數設定
Hardware Required:
Board , Stencil , Tactile ,
Please install a stencil now. (請現在放入鋼板)
Calc. Pre-Boardstop-X
-----Warning Message-----
X AXIS – SOFTWARE LIMIT WARNING!
Press NEXT to Continue.
Stencil
Pre board stop position learned
Press SELECT to continue
Press Done when finished.
Please install a stencil now.
The FRAME CLAMPS will activate when
you press NEXT.
Press NEXT to Continue, or EXIT to Quit.
28
The FRAME CLAMPS will activate when (按 NEXT 後,啟動鎖住鋼板)
you press NEXT.
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息及視窗：
The next step is to set STENCIL HEIGHT. (然後進行測鋼板高度)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息及視窗：
CAUTION, The machine is now going to(警告,機器現在要移動,內部不能有
move. STAY CLEAR.任何東西,需清除)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息及視窗：
Press SELECT to JOG the sensor clear of(按 SELECT 移動偵測感應器,勿
The next step is to set STENCIL HEIGHT.
Press NEXT to Continue, or EXIT to Quit.
CAUTION, The machine is now going to
move. STAY CLEAR.
Press NEXT to Continue, or EXIT to Quit.
Press SELECT to JOG the sensor clear of
paste or stecil apertures,
or Press NEXT to CONTINUE.
Press SELECT or NEXT to Continue.
29
paste or stecil apertures,碰到鋼板上錫膏及鋼板上 PAD 孔)
or Press NEXT to CONTINUE. (按 NEXT 馬上開始在本位置偵測鋼板高度)
Press SELECT or NEXT to Continue. (按 SELECT 或 NEXT 繼續)
你按 SELECT 之後，出現下列訊息及視窗：
JOG ACTIVE…(移動現在刮刀行程位置)
SQUEEGEE STROKE -112.050
Press EXIT to quit. (按 EXIT 離開)
你按 NEXT 與 EXIT 之後，出現下列訊息及視窗：
(開始載入 PCB,自動偵測鋼板高度)
Stencil height FOUND. (完成偵測鋼板高度)
Press NEXT to Continue. (按 NEXT 繼續下一步驟)
1.5 選擇 Squeegee 進入測刮刀高度與刮刀行程參數設定
JOG ACTIVE…
SQUEEGEE STROKE -112.050
Press EXIT to quit.
Locating the board…
CAUTION：Auto height sensor in
Stencil height FOUND.
Press NEXT to Continue.