MPM全自动印刷机中文操作手册 - 第30页
30 Hardware Required: Squeegee Blades , S tencil , T ac tile This Utility will set the SQUEEGEE height. ( 使用測刮刀高度) Pr ess NEXT to Continue, or EXIT to quit. ( 按 NEXT 繼續 , 按 EXIT 離開 ) 按 NEXT 之後，出現下列訊息視窗： Please install a …
29
paste or stecil apertures,碰到鋼板上錫膏及鋼板上 PAD 孔)
or Press NEXT to CONTINUE. (按 NEXT 馬上開始在本位置偵測鋼板高度)
Press SELECT or NEXT to Continue. (按 SELECT 或 NEXT 繼續)
你按 SELECT 之後，出現下列訊息及視窗：
JOG ACTIVE…(移動現在刮刀行程位置)
SQUEEGEE STROKE -112.050
Press EXIT to quit. (按 EXIT 離開)
你按 NEXT 與 EXIT 之後，出現下列訊息及視窗：
(開始載入 PCB,自動偵測鋼板高度)
Stencil height FOUND. (完成偵測鋼板高度)
Press NEXT to Continue. (按 NEXT 繼續下一步驟)
1.5 選擇 Squeegee 進入測刮刀高度與刮刀行程參數設定
JOG ACTIVE…
SQUEEGEE STROKE -112.050
Press EXIT to quit.
Locating the board…
CAUTION：Auto height sensor in
Stencil height FOUND.
Press NEXT to Continue.
30
Hardware Required:
Squeegee Blades , Stencil , Tactile
This Utility will set the SQUEEGEE height.(使用測刮刀高度)
Press NEXT to Continue, or EXIT to quit. (按 NEXT 繼續, 按 EXIT 離開)
按 NEXT 之後，出現下列訊息視窗：
Please install a stencil now. (現在請放入鋼板)
The REAME CLAMPS will activate when(按 NEXT 之後,啟動鋼板固定夾)
you press NEXT.
Press NEXT to Continue, or EXIT to quit. (按 NEXT 繼續, 按 EXIT 離開)
按 NEXT 之後，出現下列訊息視窗：
You must now install the squeegee blade. (你現在必須安裝刮刀)
Press NEXT to Continue, or EXIT to quit. (按 NEXT 繼續, 按 EXIT 離開)
Squeegee
This Utility will set the SQUEEGEE height.
Press NEXT to Continue, or EXIT to quit.
Please install a stencil now.
The REAME CLAMPS will activate when
you press NEXT.
Press NEXT to Continue, or EXIT to quit.
You must now install the squeegee blade.
Press NEXT to Continue, or EXIT to quit.
31
按 NEXT 之後，出現下列訊息視窗：
CAUTION, The machine is now going to(注意,機器的 Z 軸和刮刀上下將
Move the Z TOWER and cycle 會移動)
the SQUEEGEE UP and DOWN.
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
按 NEXT 之後，出現下列訊息視窗：
Press SELECT to find Stencil Height(按 SELECT 之後,再測一次鋼板高度
or NEXT to Bypass. 按 NEXT 之後,不測鋼板高度)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
按 NEXT 之後，出現下列訊息視窗：
Press SELECT to JOG the sensor clear of(按 SELECT 移動偵測感應器,勿
paste or stencil apertures 碰到鋼板上錫膏及鋼板上 PAD 孔)
CAUTION, The machine is now going to
Move the Z TOWER and cycle
the SQUEEGEE UP and DOWN.
Press NEXT to Continue, or EXIT to Quit.
Press SELECT to find Stencil Height
or NEXT to Bypass.
Press NEXT to Continue, or EXIT to Quit.
Press SELECT to JOG the sensor clear of
paste or stencil apertures
or press NEXT to CONTINUE.
Press SELECT or NEXT to Continue.