MPM全自动印刷机中文操作手册 - 第71页
71 Pr ess SELECT to JOG the sensor clear of ( 按 SELECT 移動偵測感應器 , 以 paste or stencil apertures, 免碰到鋼板上錫膏及鋼板上 P AD 孔 ) or Press NEXT to CONTINUE. ( 按 NEXT 馬上開始在本位置偵測鋼板高度 ) Pr ess SELECT or NEXT to Continue. ( 按 SELECT 或 NE…
70
看 PC 板吸真空是否定位良好及調整支撐
PIN(Support PIN)位置。
4. Begin：開始送板到印刷區位置並依照上述設定上升高度
5. Detent：載入 PC 板向前與向後於中心點位置
6. Exit ：跳出手動進板的畫面,回到主畫面
2. Stencil Height
測 PCB 板到鋼板厚度
This utility will the set STENCIL height. (要開始使用偵測鋼板高度)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息及視窗：
CAUTION, The machine is now going to(警告,機器現在要移動,內部不能有
move. STAY CLEAR.任何東西,需清除)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 NEXT 之後，出現下列訊息及視窗：
This utility will the set STENCIL height.
Press NEXT to Continue, or EXIT to Quit.
CAUTION, The machine is now going to
move. STAY CLEAR.
Press NEXT to Continue, or EXIT to Quit.
Press SELECT to JOG the sensor clear of
paste or stencil apertures,
or Press NEXT to CONTINUE.
Press SELECT or NEXT to Continue.
71
Press SELECT to JOG the sensor clear of(按 SELECT 移動偵測感應器,以
paste or stencil apertures, 免碰到鋼板上錫膏及鋼板上 PAD 孔)
or Press NEXT to CONTINUE. (按 NEXT 馬上開始在本位置偵測鋼板高度)
Press SELECT or NEXT to Continue. (按 SELECT 或 NEXT 繼續)
你按 SELECT 之後，出現下列訊息及視窗：
JOG ACTIVE…(移動現在刮刀行程位置)
SQUEEGEE STROKE -112.050
Press EXIT to quit. (按 EXIT 離開)
你按 NEXT 與 EXIT 之後，出現下列訊息及視窗：
(載入基板中………)
(注意：高度自動偵測進行，請稍後………)
JOG ACTIVE…
SQUEEGEE STROKE -112.050
Press EXIT to quit.
Locating the board…
CAUTION：Auto height sensor in
Stencil height FOUND.
Press NEXT to Continus.
72
Stencil height FOUND. (完成偵測鋼板高度)
Press NEXT to Continue. (按 NEXT 繼續下一步驟)
3. Set Stroke
設定刮刀組行程
This utility will allow you to set the (本功能可設定印刷時的刮刀行程)
SQUEEGEE STROKE used during printing.
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
你按 SELECT 之後，出現下列訊息及視窗：
Jog the SQUEEGEE to the desired +STROKE (移動刮刀到朝向鋼板後方
located toward the rear of the stencil. 的正方向適當位置)
Press NEXT to Continue, or EXIT to Quit. (按 NEXT 繼續, 按 EXIT 離開)
按 NEXT 之後，有一指標會往上跑到 JOG 區的 SQUEEGEE STROKE
This utility will allow you to set the
SQUEEGEE STROKE used during printing.
Press NEXT to Continue, or EXIT to Quit.
Jog the SQUEEGEE to the desired ＋STROKE
located toward the rear of the stencil.