cp45头部故障判断 - 第23页
1. Head Module Ver. Date CP45 CP45NEO 00 2004/11 O O 1-1 1-11.Offset-R Adjustment an d Input *T o o l s a) *P a r t a) . => Used for FV Type 1) Run R-axis Home 2) Move Axis(1-2 ,3-4, 5-6) to be Measured to Stage Camer…
1. Head Module
Ver. Date CP45
CP45NEO
00 2004/11 O O
1-1
9) Assemble Joint at the Upper Part of Ball Spline (Ref. Fig. 1-10-4)
10) After Assmbling Wavy-washer, V-Ring, Joint(J7155167D), Assemble Z-axis Spring (Ref. Fig. 1-10-5)
( V-Ring Specification; V-6A,Assemble Direction;
)
11) Assemble Nozzle Holder
12) Assemble Spring Cab and Spline Spring
=> Check Vacuum to See if There is Wrong Assemble Part in Diagnosis
* Adjustments after this work
- Head(Fly) Camera Calibration.(Ref. 2-3)
- Head offset Setting.(Ref. 2-16)
- Vision Nozzle Check.(Ref. 1-12)
Fig.1-10-4 Joint set-up
Joint(J7155168A)
Slide Arm
Joint(J7155167D)
Wavy Washer
(J6049000550)
V-Ring(J6304001A)
Fig.1-10-5 V-Ring set-up
1. Head Module
Ver. Date CP45
CP45NEO
00 2004/11 O O
1-1
1-11.Offset-R Adjustment and Input
*Tools
a)
*Part
a)
.
=> Used for FV Type
1) Run R-axis Home
2) Move Axis(1-2 ,3-4, 5-6) to be Measured to Stage Camera
(Select Sys. Setup => Camera => Stage Camera => Camera Position to Move)
3) Arrange the Groove of Nozzle Holder with low speed of Teaching Box Watching Monitor,
andCheckthePositionofR-axisat'CurrentPosition'
4)
Input This Value at Head Z-Motor Offset for Compensation (Ref. Fig 1-11-1)
(Compensation Value Check at Current Position is Added with '-' and Inputted)
Fig1-11-1HeadZHomeOffset
1. Head Module
Ver. Date CP45
CP45NEO
00 2004/11 O O
1-1
1-12. Nozzle Check Function Setting (for Former Serial No ~1188 Equipment)
*Tools
a)
1-12-1) When Using Nozzle Check Sensor
1-12-1-1) Select I/O Test of Diagnosis Menu to Check if Nozzle Check Sensor Works
- Turn Sensor ON/OFF with Mouse to Check
- Check ON/OFF by Covering Sensor with Paper (Check Assembled Condition)
1-12-1-2) Insert TN05 in HEAD3 (Use PICK Function of ANC)
- Note : Don't Insert Manually
1-12-1-3) Open Menu - View - Current position
1-12-1-4) Lower Head to 60mm with Teaching Box
1-12-1-5) Change the Switch of Sensor Amp to Set Mode
1-12-1-6) Turn the Switch of Sensor Amp ON
1-12-1-7) Lower Head3 to 50mm with Teaching Box
1-12-1-8) Turn the Switch of Sensor Amp OFF
1-12-1-9) Change the Switch of Sensor Amp to Run Mode
1-12-1-10) Slowly Move Head3 to 57mm (with Teaching Box)
Setting is OK if Green and Red LED are Both ON at 57.0 ~ 58.0mm.
Only Green LED is ON if Head3 Keeps Going Down
Reset from 1-12-1-4) if Green LED is OFF or Red LED is ON
- Increase the Height of Head3 in 1-12-1-7) by 1mm for Setting
- If the Height is Increased to 55.0mm in 1-12-1-7) and There is No Change of Sensing
Distance, Use it w/o Further Change
1-12-1-11) Check if Sensor Works at ANC Screen
IfArbitraryHeadw/oNozzleisUsedtoSelectArbitraryANCNumberw/oNozzleand
PICK is Clicked, in Normal Case the Error Message that There is No Nozzle in Head is
ALIGN HEIGHT
=54.5mm
PCB PCB
NOZZLE CHECK HEIGHT
=59.0mm
NOZZLE CHECK
SNESOR
Fig.1-12
Nozzle Check Sensor setting.