192277 - Micron Technical Reference Volume 3 - 第173页
PASTE ROLL HEIGHT MONITOR MECHANICAL DETAIL Chapter Issue 3, Aug 14 Technical Reference Manual 30.5 MECHANICAL DET AIL Roll Height Monitor Assembly The Roll Height Monitor assembly cons ists a horizontal beam which is se…
PASTE ROLL HEIGHT MONITOR
ELECTRICAL SCHEMATIC
30.4 Technical Reference Manual Chapter Issue 3, Aug 14
ELECTRICAL SCHEMATIC
Paste Level
Sensor
9SE15
Roll Height
Sensor
9SE24
Roll Height
Laser
+12V
Signal
0V
+12V SW
Signal
0V
+12V SW
0V
N3PL11
N3PL4
DIG IN 9
DIG IN 2
Paste Cartridge
Horizontal Sensor
9SE13
N3PL10
DIG IN 8
Paste Pressure
Solenoid
9SOL26
N3PL8
DIG OUT 4
Paste Cartridge
Tilt Actuator
9SOL27
N3PL8
DIG OUT 5
Paste Cartridge
Vertical Sensor
9SE14
N3PL10
DIG IN 7
Print Carriage
Print Carriage
I/O Node 3
Paste Dispense
Stepper Node 10
N3SK2
N3SK3
N10PL4
PC
Single Board
Computer (SBC)
or
Motherboard
USB
CAN
Out
CAN
Out
CAN
In
M36PL35
NextMove ES
(I/O Node 1)
M36 Machine Control
N3SK3
CAN Bus
CAN
In
NOTE
The breaks in the CAN Bus chain reflect that additional
I/O Nodes may be fitted, refer to Machine Control
chapter for the complete CAN Bus chain.
Paste Dispenser
Home Sensor
9SE12
+24V
Signal
0V
N10PL1
M
I/O3
N3PL44
N3PL44
9PL27
9PL26
9SE12
M37 PSU
Enclosure
+24V US
0V Return
+24V SW
0V Return
+12V
0V Return
N10SK2
M37PL08
+24V US
0V Return
+24V SW
0V Return
+12V
0V Return
N3SK1
M37PL05
9PL60
PASTE ROLL HEIGHT MONITOR
MECHANICAL DETAIL
Chapter Issue 3, Aug 14 Technical Reference Manual 30.5
MECHANICAL DETAIL
Roll Height Monitor
Assembly
The Roll Height Monitor assembly consists a horizontal beam which is secured
to the machine in place of the front squeegee ‘I’ beam. Two legs attached at
either end of the beam via THK linear bearings, house the laser light source and
receiver. Plastic wedges at the foot of each leg prevent damage to the stencil
whilst the print stroke is being carried out. The horizontal beam houses beam
extensions which can vary the beam’s length from 421mm to 575mm to
accommodate different size squeegees. Each extension is secured within the
beam by a cap headed bolt.
Figure 30-1 Roll Height Monitor Assembly
NOTE
The paste drip tray must be removed before fitting the paste roll height monitor.
Voltage Regulator The voltage regulator situated within the looms at the right rear corner of the
machine. The regulator provides the correct voltage to the roll height sensor.
View on Arrow A
Showing Light Receiver
A
Paste Height Adjustment
Securing Screw
(in 2 positions)
Nylon Screen Protector
(in 2 positions)
Laser Transmitter
THK Linear Bearing
(in 2 positions)
Width Adjustment Securing Screw
(in 2 positions)
Front Squeegee
Mount
Horizontal Beam
PASTE ROLL HEIGHT MONITOR
DRIVES & SENSORS
30.6 Technical Reference Manual Chapter Issue 3, Aug 14
DRIVES & SENSORS
Drives There are no drives associated with this option.
Sensors
Name Type Control Card Functional Description
Roll Height
Sensor
9SE24 MultiMove X11 Detects the laser light when the print
medium is insufficient.