CM602all_EJM8AESM_Service Manual - 第709页
Machinery Part Replacement This section describes the procedures for replacing the main body of the nozzle changer (12-nozzle head). Tools Allen key 3 mm Allen key 5 mm Pipe Nipper Dial gauge Magnetic stand Iron plate Ji…
Machinery Part Replacement
Remarks
List of differences between 12-nozzle-head and 8-nozzle-head teaching jigs
12-Nozzle Head Teaching
1
Item
R
e
f
e
r
e
n
ce
n
o
zzl
e
pos
i
t
i
o
n f
o
r
eac
h h
ead
8-nozzle head
12-nozzle head No. 5
No. 3
12ノズル
手順書
基板認識
カメ
ラ
XY
軸原点オ
フセ
ッ
幅調整軸原点オフセット
基板位置決め実装高さ
面補正
吸着位置
照明光量
ノズ
ルチ
ェ
ンジャ
実装位置
(ヘッドカメラ調整)
130ノズル
8ノズル用5穴治
130Sノズル
(同一作業)
130ノズル
50 治具
130Sノズル
他同一治具使用
面補正治具使用
同一治具使用
130ノズル
吸着位置ティーチ治具
130Sノズル
他同一治具使用
透過・反射治具ノズル使
130Sノズル
8ノズル用ティーチ治具
130Sノズル
12ノズル用ティーチ治具
130ノズル
8ノズル用ティーチ治具
110・205ノズル使用
110S・205Sノズル
他同一治具使用
Share
同一治具使用
Item
8 nozzles
12 nozzles
Board recog camera XY-axis origin offset
Z-axis origin offset
Chip recog camera θ-axis origin offset
Width adjusting axis origin offset
Board positioning mounting height
XY plane calibration
Pickup position
Light intensity
Nozzle changer
Mount position
(Head camera adjustment)
Nozzle 13
0
8-nozzle 5-hole jig
Jig 50
Nozzle 130
XY Plane calibration jig
Pickup position teaching jig
Nozzle 130
The others: the same jig
Nozzle 130S
The others: the same jig
Nozzle 130S
12-nozzle teaching jig
Nozzle
Nozzle 110S and 205S
The others: the same jig
The same jig
The same jig
8-nozzle teaching jig
Nozzle 130
Shadow & Direct nozzle jig
Nozzles 110 & 205
12-nozzle 5-hole jig
Nozzle 130
S
(The same adjustment)
12-
manual
Share
Share
Available
Available
Available
Available
Available
Available
Available
EJM8A-E-SMA051112-A01-00
Page 5-11-12-2
Machinery Part Replacement
This section describes the procedures for replacing the main body of the nozzle changer (12-nozzle head).
Tools
Allen key 3 mm
Allen key 5 mm
Pipe
Nipper
Dial gauge
Magnetic stand
Iron plate
Jig
Nozzle-changer-
teaching jig
Nozzle 130S
Nozzle Changer (12-nozzle) Unit
5-12-1 Main Body of Nozzle Changer (12-Nozzle Head)
12-nozzle-change-
position-teaching jig
Nozzle Chan
g
er
(
12-Nozzle S
p
ec.
)
Unit5-12
Dange
r
Caution
Warning
EJM8A-E-SMA051201-A01-00
Page 5-12-1-1
Machinery Part Replacement
Remarks
Turn off the main power.
Turn the switch to the left.
Close the MR-unit cock.
After closing the cock, turn the regulator
to the left, and release the air.
* The gauges are lined from the left as
follows: compulsory blow, bulk air and
main air.
0.49MPa to
0.54MPa
Remove the feeder cover and the chute.
Allen key 3 mm
M4 screw 4 pcs.
Remove the right side cover.
Remove the feeder cover.
Remove the tape-float-sensor cover from
the main body.
Allen key 3 mm
M4 screw 4 pcs.
Nozzle Changer (12-nozzle) Unit
4
1
Item
2
3
1
2
EJM8A-E-SMA051201-A01-00
Page 5-12-1-2