User Manual - SIPLACE Glue Feedeer - 第87页
5 Cleaning and Maintenance 5.5 Replacing the Cartridge User Manual SIPLACE Glue Feeder 05/2020 87 ► Hold the cartridge against the cartridge pipe and screw it on to the pipe straight. ► Fit the cartridge adapter at the s…
5 Cleaning and Maintenance
5.5 Replacing the Cartridge
86 User Manual SIPLACE Glue Feeder 05/2020
5.5.2 Inserting the Cartridge
Two sizes of cartridge can be used with the Glue
Feeder (10 or 30 ml).
► Adjust the cartridge holder to the size of the cart-
ridge to be used.
1. Then pull out the cartridge holder.
2. Turn the cartridge holder so that the required size
is at the top.
3. Let the cartridge holder engage audibly.
If you want to use a different size of cartridge to that
which is set, you will need to also replace the cartridge
holder.
► Pull the hose off the cartridge adapter.
► Fit the hose as far as the stop onto the corres-
ponding cartridge adapter for your size of cart-
ridge.
► Fix the hose with a cable tie.
► Screw the front cap off the cartridge.
► Remove the back cap from the cartridge.
5 Cleaning and Maintenance
5.5 Replacing the Cartridge
User Manual SIPLACE Glue Feeder 05/2020 87
► Hold the cartridge against the cartridge pipe and
screw it on to the pipe straight.
► Fit the cartridge adapter at the straight points
onto the back of the cartridge and press on as far
as the stop.
► Turn the cartridge adapter clockwise onto the
cartridge, as far as the stop.
► Make sure that the O-ring on the cartridge adap-
ter is completely flush against the inside of the
cartridge and seals it. If not, the required working
pressure will not form.
To make it easier to insert the adapter with the
O‑ring, you can grease the O-ring slightly (Tur-
motemp II/400 CL2).
NOTICE
Predosing
Although you have inserted the cartridge, the Glue Feeder is still not ready for use. You first
need to position the Glue Feeder at the required location and predose the glue unit (cart-
ridge pipe, jet block and dispenser nozzle) i.e. fill it with glue. For a detailed description,
refer to section 3.5
"Predosing the Glue Feeder" [}30].
5 Cleaning and Maintenance
5.6 Guide Bushing and Actuator O-Ring
88 User Manual SIPLACE Glue Feeder 05/2020
5.6 Guide Bushing and Actuator O-Ring
The tasks described in this section are performed 1x month.
It is wise to combine these tasks with cleaning and inspecting the glue unit (see section 5.4 "Clean-
ing and Inspecting the Gluing Unit" [}70]) as this unit has already been taken apart for these tasks.
5.6.1 Removing the Actuator O-Ring and Guide Bushing
► Unscrew and take apart the glue unit (see section 5.4.1 "Dismantling the Gluing Unit" [}70]).
► If necessary, clean the glue unit (see section 5.4.2 "Cleaning the Gluing Unit" [}75]).
► Place the Glue Feeder to one side and pull it up to the edge of the table.
DANGER
Risk of damage
Never exert side forces against the plunger. The valve could be seriously damaged by this.
This would cause the Glue Feeder to malfunction.
► Clean the jet plunger again with a cleansing tis-
sue and a little glue remover.
► Use the extraction tool set for the jet valve plun-
ger (item no. 03216329-xx) to reliably pull out the
plunger.
The extraction tool set includes:
●
Tool holder with square nut I=110 (item no.
03216547-xx) (1)
with a large (A) and a small (B)
clamping insert
●
2 guide profiles (2)
●
4 screws ISO 4762 – M3 x 40-A2-70 (item no.
03216547-xx) (3)
for fastening the guide profiles