FUJI错误代码查询 - 第1182页

Remedy: Make the device description tolerance settings (pickup tolerance x, pickup tolerance y, rotation tolerance) smaller. Generally, if the parts are small, the edge of the nozzle protrudes, and this makes the vacuum …

Coarse_edge_d2

Coarse_edge_e1_polarity

Coarse_edge_e3_polarity

break_rate

max_break

------------------------------

Code: 1C410123

Display:

Used by:

Cause: Pickup tolerance is too large.

Remedy: Make the GD tolerances (pickup tolerance x, pickup tolerance y, rotation tolerance) smaller. This

error generally means that part pickup rates are bad. Check pickup conditions at the monitor.

------------------------------

Code: 1C410124

Display:

Used by:

Cause: Pickup tolerance is too large.

Remedy: Make the GD tolerances (pickup tolerance x, pickup tolerance y, rotation tolerance) smaller. This

error generally means that part pickup rates are bad. Check pickup conditions at the monitor.

------------------------------

Code: 1C410125

Display:

Used by:

Cause: A preset time limit has been exceeded.

Remedy: Set Part data's PD.Cam_speed lower. Check to see if the part can be placed at 100% cam speed.

------------------------------

Code: 1C410126

Display:

Used by:

Cause: Even though coarse edge was performed, the pickup tolerance is too large.

Remedy: Make the GD tolerances (pickup tolerance x, pickup tolerance y, rotation tolerance) smaller.

------------------------------

Code: 1C410127

Display:

Used by:

Cause: The coarse edge could not be found.

Remedy: Set up a correct coarse edge description. Check the following:

Coarse_edge_angle

Coarse_edge_l1

Coarse_edge_d1

Coarse_edge_l2

Coarse_edge_d2

Coarse_edge_e1_polarity

Coarse_edge_e3_polarity

break_rate

max_break

------------------------------

Code: 1C410128

Display:

Used by:

Cause: Training cannot be done because the pickup tolerance is too large.

第 1181 页

Remedy: Make the device description tolerance settings (pickup tolerance x, pickup tolerance y, rotation

tolerance) smaller. Generally, if the parts are small, the edge of the nozzle protrudes, and this makes the

vacuum weaker, and the parts can therefore easily slide after vision processing is complete. Caution must

be exercised on this point.

------------------------------

Code: 1C410129

Display:

Used by:

Cause: Training cannot be done because the coarse edge is incorrect.

Remedy: Enter a correct device description coarse edge. Check the following:

Coarse_edge_angle

Coarse_edge_l1

Coarse_edge_d1

Coarse_edge_l2

Coarse_edge_d2

Coarse_edge_e1_polarity

Coarse_edge_e3_polarity

break_rate

max_break

------------------------------

Code: 1C410130

Display:

Used by:

Cause: The coarse edge pickup tolerance is too large.

Remedy: Make the device description tolerance settings (pickup tolerance x, pickup tolerance y, rotation

tolerance) smaller.

------------------------------

Code: 1C410131

Display:

Used by:

Cause: The coarse edge tolerance (positional uncertainty) is too large.

Remedy: Make the generic device description tolerance settings (pickup tolerance x, pickup tolerance y,

rotation tolerance) smaller.

------------------------------

Code: 1C410132

Display:

Used by:

Cause: The blob cannot be found in the nozzle position.

Remedy: If the nozzle seen at the monitor is not dirty, this is probably a hardware problem.

------------------------------

Code: 1C410133

Display:

Used by:

Cause: A blob analysis failed to determine the device rotation angle during inspection. However, device

training indicated that the angle could be determined. Therefore the run-time image is not what the

software expects based on the device description. Pickup uncertainty is large enough to require that blob

analysis be used during device inspection. In such cases, during device training, the system uses the

device description to predict whether useful angle information will appear in the blob results. If the

system expects angle information to appear and it does not, then this error occurs.

Remedy: Check that the direction is correct. Also, check the part placement direction in PD. If the nozzle

edge protrudes from the part (the nozzle is too large) this error can also occur. Either improve the

第 1182 页

accuracy of the device description, or reduce the pickup uncertainty so that blob analysis is no longer

required.

------------------------------

Code: 1C410134

Display:

Used by:

Cause: There is insufficient data in the generic device description.

Remedy: Fix the generic device description. If this error occurs often, contact Fuji.

------------------------------

Code: 1C410139

Display:

Used by:

Cause: The nozzle edge is protruding from the part.

Remedy: Make the nozzle size smaller. If this error occurs often, contact Fuji.

------------------------------

Code: 1C410142

Display:

Used by:

Cause: The vision processing program angular uncertainty calculations are contradictory.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C410143

Display:

Used by:

Cause: The caliper window does not fit properly.

Remedy: Optically reduce the image magnification, correct the pickup nozzle, or center the nozzle in the

field of view. That is, make the generic device description tolerance settings (pickup tolerance x, pickup

tolerance y, rotation tolerance) smaller.

------------------------------

Code: 1C410144

Display:

Used by:

Cause: The input nozzle size value is not the same as the actual value.

Remedy: Input the correct value in the production program and retransmit the program.

------------------------------

Code: 1C420002

Display:

Used by:

Cause: The command to the vision processing system is abnormal.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420004

Display:

Used by:

Cause: A command made to vision processing is incorrect.

Remedy: If this error occurs often, contact Fuji.

------------------------------

Code: 1C420007

Display:

Used by:

Cause: A command made to vision processing is incorrect.

第 1183 页