FUJI错误代码查询 - 第1191页

equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then not enough leads were detected. Remedy: If "??" equals 0A, 0B, 0C, 0D, 15, or 18 this indicates that the necessary number of corners (more than two) were …

Code: 1CA??004

Display: 1CA??004

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 15, or 18 this signifies that the search for the part boundaries could not begin because the nozzle

is bent. If "??" equals 14 or 28 then there is an error in the descriptions of the leads in part data. If "??"

equals 16 or 17 this indicates that the lead descriptions in part datahave been set to "0". If "??" equal FC

then the part's Y-direction size exceeds the tolerance value.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 15, or 18 then the nozzle center of rotation and the image of the

nozzle do not conform. Make sure the nozzle is not bent. If "??" equals 14, 16, 17, or 28 then make the

necessary corrections to the lead descriptions in part data. If "??" equal FC then the part size is incorrect.

Correct the part data.

------------------------------

Code: 1CA??005

Display: 1CA??005

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 15, or 18 this signifies that the part outline could not be found. If "??" equals 14 or 28 this

indicates that the lead pitch setting is either too narrow or too wide. If "??" equals 16 or 17 then the lead

width is smaller than the lead pitch. If "??" equal 7B, 7C, 96, 97, 98, 99, F0 or FE then invalid "P_Pattern"

value.

Remedy: If "??" equals 0A, 0B, 0C, or 0D then make sure that there are no unexpected protrusions

resulting from a burr or something being stuck to the part. If "??" equals 14, 16, 17, or 28 then make the

necessary corrections in part data. If "??" equals 15 or 18 then make sure that there are no unexpected

protrusions resulting from a burr or something being stuck to the part. If there is a protrusion on any

side other than the side opposite the lead segment on one portion of the part, then this Visio _type cannot

be used. Try using vision processing number 20 or 100 in such a case. If "??" equal 7B, 7C, 96, 97, 98,

99, F0 or FE then "P_Pattern" must be 1 to 16, 23, 24, 33 or 34.Check the "P_Pattern" setting.

------------------------------

Code: 1CA??006

Display: 1CA??006

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 15, or 18 this signifies that part positioning was not possible because there were too many

segments in the outline of the part. If "??" equals 14 or 28 then there are bent leads. If "??" equals 16 or

17 this indicates that the part could not be found because the nozzle was bent. If "??" equal 64, 78, 79,

7A, 7B, 7C, 96, 97, 98, 99, A0, F0 or FE then invalid "Result" value.

Remedy: If "??" equals 0A, 0B, 0C, or 0D then the part has too many slight protrusions such as burrs

causing breaks in the linear segments. If "??" equals 14 or 28 this indicates that the bend in the leads has

exceeded the permissible range specified in the pitch limit in part data. If "??" equals 15 or 18 then the

part has too many slight protrusions such as burrs causing breaks in the linear segments. Try

Vision_type 20 or 100 in such a case. If "??" equals 16 or 17 then either re-measure the nozzl center or

replace with another nozzle. If "??" equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99, A0, F0 or FE then this

algorithm is not compatible with matrix tables.Check whether 128 is input at "Result".

------------------------------

Code: 1CA??007

Display: 1CA??007

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 15, or 18 then the part pickup status is bad. If "??" equals 14 or 28 this indicates that not a

single lead was detected. If "??" equals 16 or 17, the inspected leads were smaller than specified. If "??"

第 1190 页

equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then not enough leads were detected.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 15, or 18 this indicates that the necessary number of corners

(more than two) were not found for determining the part position. Make sure that the nozzle is not bent

and that the part is being properly picked from the feeder. If "??" equals 14 or 28 then make sure that the

part data is correct. In particular make sure that the P_pattern setting is correct. If "??" equals 16 or 17

then check the part data. If the part data is satisfactory then decrease the Body_ and Body_y settings in

Tolerance information. If "??" equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then a minimum of two

leads must be detected.Check the number of leads set, and "Result".

------------------------------

Code: 1CA??008

Display: 1CA??008

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 10, 15, or 18 this signifies that the X-dimension of the part has exceeded the permissible range. If

"??" equals 14 or 28 then a lead was found in a location where no lead was expected. If "??" equals 16 or

17 then the inspected leads were larger than specified. If "??" equal 7B, 7C, 96, 97, 98, 99, F0 or FE then

invalid lead width value.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 10, 15, or 18 then the part size is wrong. Make sure that the part

data is correct. If "??" equals 14 or 28 then verify that the lead arrangement information is correct. Also,

be sure that the correct part is being used. If "??" equals 16 or 17 then check the part data. If the part

data is satisfactory then increase the Body_x and Body_y settings in Tolerance information. If "??" equal

7B, 7C, 96, 97, 98, 99, F0 or FE then the lead width input is 0 or less. Check the lead width.

------------------------------

Code: 1CA??009

Display: 1CA??009

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 0A, 0B,

0C, 0D, 10, 15, or 18 this signifies that the Y-dimension of the part has exceeded the permissible range.

Remedy: If "??" equals 0A, 0B, 0C, 0D, 10, 15, or 18 then the part size is wrong. Make sure that the part

data is correct.

------------------------------

Code: 1CA??00A

Display: 1CA??00A

Used by:

Cause: If "??" equals 0D or 18 then the supply orientation of the part is incorrect. If "??" equal 64, 78, 79,

7A, 7B, 7C, 96, 97, 98, 99 or F0 then invalid lead length value.

Remedy: If "??" equals 0D the error has occurred as a result of the direction test that is utilized when

tantalum sprague components are processed. If "??" equals 18 the error has occurred as a result of the

direction test that is utilized when trimmer resistor components are processed. Set the correct supply

orientation. If "??" equal 64, 78, 79, 7A, 7B, 7C, 96, 97, 98, 99 or F0 then the lead length input is 0 or

less. Check the lead length.

------------------------------

Code: 1CA??00B

Display: 1CA??00B

Used by:

Cause: If "??" equals 0A, 14 or 28 this signifies that positioning could not be determined correctly

because the image was oscillating. If "??" equal A0 then the part angle is being obtained incorrectly. If "??"

equal 64, 78, 79, 7A, 7B, or 7C then the element size is larger than the body size.

Remedy: If "??" equals 0A, 14 or 28 then this error occurs on the FCP5. Carry out readjustment of the

index servo. If "??" equal A0 then check to see if burrs on the part edges, or dust on the background is

causing an image problem. If "??" equal 64, 78, 79, 7A, 7B, or 7C then check the element size and the

第 1191 页

body sized.

------------------------------

Code: 1CA??00C

Display: 1CA??00C

Used by:

Cause: If "??" equals 28 this signifies that the body has failed to be detected. If "??" equal A0 then the

body edge cannot be detected. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then invalid lead pitch value.

Remedy: If "??" equals 28 then check the dimensions of the part. If "??" equal A0 then check for errors in

the part data's "part size" setting, and in the element_data detection position. If "??" equal 64, 78, 79, 7A,

7B, 7C or F0 then the lead pitch is smaller than the lead width.Check the lead pitch and the lead width.

------------------------------

Code: 1CA??00D

Display: 1CA??00D

Used by:

Cause: If "??" equals 28 this signifies that there were no body detection points. If "??" equal A0 then

mismatch between the part size and the part data. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then there are

overlapping elements.

Remedy: If "??" equals 28 then the results of calculating the body detection points using the body data

prevented the body from being detected because the leads were concealed by the body. If "??" equal A0

then specify the correct part size in part data. When there is a large size difference from part to part,

specify a large tolerance value. If "??" equal 64, 78, 79, 7A, 7B, 7C or F0 then check the element data, and

ensure none of the elements are overlapping.

------------------------------

Code: 1CA??010

Display: 1CA??010

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 78,

79, 96, 99, 9B or 9E this signifies that the positioning phase could not be determined. If "??" equal A0

then coarse positioning is not possible. If "??" equal F0, F1 or F2 then search failed.

Remedy: If "??" equals 64, 78, or 79 this indicates that there is a problem with the brightness of the

image. Make sure that there is no dirt or dust reflected in the background. If "??" equals 96,99, 9B or 9E

then verify that the part and mechanical chuck do not lie outside of the camera field of vision. Also make

sure that there is not a problem with the brightness of the image and that there are no contaminants

reflected in the background.

If "??" equal A0 then cCheck for the following:

o Part or mechanical chuck protruding from the camera's field of vision.

o Image brightness problem.

o Image problem caused by dust, etc., on the part background.

When a nozzle is being used, the size of the nozzle's reflective disk should be at least 1.7 times the part

size.

If "??" equal F0, F1 or F2 then check for errors in the part data. Create a model to reduce the size of the

circumscribed square outline for the entire model.

------------------------------

Code: 1CA??011

Display: 1CA??011

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 1E, 64,

78, 79, AC, or FE then boundary detection could not begin because the nozzle was bent. The image lies

outside the scan area. If "??" equals 7C, 82, 83, 98, 9D or B4 this indicates that the leads could not be

acquired from the body and background. If "??" equals 8C, E6, E7 or E9 there are too few leads described

in part data. If "??" equal F0, F1 or F2 then model size exceeds the tolerance range.

第 1192 页