FUJI错误代码查询 - 第1197页

------------------------------ Code: 1CA??037 Display: 1CA??037 Used by: Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69, 78, 79, 7A, 7B, 7C, …

part data is correct then make sure there is not too much displacement in the part pickup status. If "??"

equals 8D or 8E Check for the following:

o Part protruding from the camera's field of vision.

o Image brightness problem.

o Image problem caused by dust, etc., on the part background.

------------------------------

Code: 1CA??033

Display: 1CA??033

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0 or F0 this indicates that there was no inspected

segment for determining the Y-dimension of the part position. If "??" equals 8C, 8D, 8E, E6, E7, E9, EB,

or EC this indicates that the number of leads found is less than the specified number of leads. If "??"

equals 98 or 9D then there was alead recognition failure.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0, or F0 this means that

the inspection of leads has failed for some reason. Leads could not be found for the Y-dimension

inspection results to be used for part positioning. Make sure that the data set in P_pattern in part data is

appropriate. If "??" equals 8C, 8D, 8E, E6, E7, E9, EB, or EC this signifies that part positioning was

carried out but that the number ofleads detected was less than the number of leads specified. Decrease

the Check_limit setting in part data. f "??" equals 98 or 9D then make sure the part data is correct. In

particular verify that the lead size has been input correctly.

------------------------------

Code: 1CA??034

Display: 1CA??034

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, or F0 this indicates that the leads used for determining positioning could not be

detected. If "??" equals 96, 97, 99, 9B, 9C, or 9E this signifies that there was no data for calculating the

angles. If "??" equal A0 data required for angle calculation does not exist.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, or F0 this means that the leads could not be found

for the inspection results to be used for part positioning. Make sure that the data set in P_pattern in part

data is appropriate. If "??" equals 96, 97, 99, 9B, 9C, or 9E then verify that the part data is correct. If "??"

equals A0 check for errors in the part data.

------------------------------

Code: 1CA??035

Display: 1CA??035

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0 or F0 this signifies that a lead was detected in a

location where no lead was expected.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7D, 7E, 7F, 96, 97, 99, 9B, 9C, 9E, A0 or F0 then make sure

the lead arrangement data is correct. Also verify that the correct part is being used.

------------------------------

Code: 1CA??036

Display: 1CA??036

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7B, 7C, 7D, 7E, 7F, 96, 97, 98, 99, 9B, 9C, 9D, 9E, A0, B4, or F0 this indicates that an excess

lead was discovered whenthe first-last lead pitch check was carried out.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7B, 7C, 7D, 7E, 7F, 96, 97, 98, 99, 9B, 9C, 9D, 9E, A0, B4, or

F0 then confirm that the correct part is being used.

第 1196 页

------------------------------

Code: 1CA??037

Display: 1CA??037

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 64, 69,

78, 79, 7A, 7B, 7C, 7D, 7E, 7F, 96, 97, 98, 99, 9B, 9C, 9D, 9E, A0, B4, or F0 this indicates that not a

single lead was detected.

Remedy: If "??" equals 64, 69, 78, 79, 7A, 7B, 7C, 7D, 7E, 7F, 96, 97, 98, 99, 9B, 9C, 9D, 9E, A0, B4, or

F0 then confirm that the part data is correct. In particular, make sure that the P_pattern setting is

correct.

------------------------------

Code: 1CA??040

Display: 1CA??040

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal F0 the

lead to be checked was not found.

Remedy: If "??" equal F0 check the part data's EL_data for errors.

------------------------------

Code: 1CA??041

Display: 1CA??041

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 80, 81, 82, 83, 87, 88, or B4 this signifies that there is no data for the X-dimension calculations. If

"??" equals 8C, 8D, 8E, E6, E7, E9, EB, or EC then the part data expressed in matrix form is incorrect. If

"??" equals 98 or 9D this indicates that there is no inspected segment for carrying out the X-dimension

positioning of the part. If "??" equal F0 the measurement point for positioning does not exist.

Remedy: If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, or B4 then make sure that the part data is correct.

If "??" equals 8C, 8D, 8E, E6, E7, E9, EB or EC this error will occur when the part is registered in the

vision processing system. The data item Result=128 in EL_data has been improperly set. When the

EL_data is expressed in matrix form, two elements represent one lead block. Correct the part data. If "??"

equals 98 or 9D then confirm that the P_pattern setting in EL_data is appropriate. If "??" equal F0 check

for errors in the part data. In particular, check the P_pattern setting found in the element data.

------------------------------

Code: 1CA??042

Display: 1CA??042

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 80, 81, 82, 83, 87, 88, or B4 this signifies that there is no data for the Y-dimension calculations. If

"??" equals 8C, E6, E7, E9, EB, or EC then there are not enough leads described in part data. If "??"

equals 98 or 9D this indicates that there is no inspected segment for carrying out the Y-dimension

positioning of the part. If "??" equals 8D or 8E too few bumps specified in part data.

Remedy: If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, or B4 then make sure that the part data is correct.

If "??" equals 8C, E6, E7, E9, EB or EC this error will occur when the part is registered in the vision

processing system. The positioning phase cannot be carried out if there are not enough leads described in

part data. Correct the part data. If "??" equals 98 or 9D then confirm that the P_pattern setting in

EL_data is appropriate. If "??" equal 8D or 8E this error occurs when registering data. Part positioning is

not possible if the total number of bumps registered at the part data's EL_data multiplied by the

Check_limit value is fewer than 2. Correct the number of registered bumps and the Check_limit.

------------------------------

Code: 1CA??043

Display: 1CA??043

第 1197 页

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 7B,

7C, 80, 81, 82, 83, 87, 88, 98, 9D or B4 this indicates that there is no data for the angle calculations. If

"??" equals 8C, E6, E7, E9, EB or EC then the part data is incorrect.

Remedy: If "??" equals 7B, 7C, 80, 81, 82, 83, 87, 88, 98, 9D or B4 then confirm that the part data is

correct. If "??" equals 8C, E6, E7, E9, EB or EC then this error will occur when the part is registered in

the vision processing system. Leads have been described such that a row of leads lies out of view. If leads

are defined in this way then the positioning phase cannot be carried out. Correct the part data such that

there are no leads outside of the field of vision.

------------------------------

Code: 1CA??044

Display: 1CA??044

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 8C,

8D, 8E, E6, E7, E9, EB or EC this indicates that there are overlapping leads defined in part data.

Remedy: If "??" equals 8C, 8D, 8E, E6, E7, E9, EB or EC then this error will occur when the part is

registered in the vision processing system. Check the EL_data in part data.

------------------------------

Code: 1CA??051

Display: 1CA??051

Used by:

Cause: ?? represents the Vision Type from the part data displayed in hexadecimal notation. In the case

where ?? = F1 or F2, the element data has been incorrectly input. It is not possible to enter consecutive

elements with a result of "128".

Remedy: When ?? = F1 or F2, and result "128" is being used, specify the result for the previous element

as a value other than "128".

------------------------------

Code: 1CA??052

Display: 1CA??052

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equals 8C,

E6, E7, E8, E9, or EA found bump while using Virtual Bump Inspection.

Remedy: If "??" equals 8C, E6, E7, E8, E9, or EA extra bump(s) found on the part. Verify that the part is

correct.

------------------------------

Code: 1CA??053

Display: 1CA??053

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal F0, F1

or F2 model corner is incorrect.

Remedy: If "??" equal F0, F1 or F2 check for errors in the part data.

------------------------------

Code: 1CA??054

Display: 1CA??054

Used by:

Cause: The Vision_type in part data is expressed using hexadecimal notation ("??"). If "??" equal F0, F1

or F2 model line segments intersect. It is not possible to create models where the line segments cross with

other models.

Remedy: If "??" equal F0, F1 or F2 check for errors in the part data.

------------------------------

Code: 1CA??055

第 1198 页