FUJI错误代码查询 - 第123页

Used by: GSP5 Cause: Edge mode is out of range. Remedy: Check Clamp_mode in the production program. A setting of 0 indicates mark reference, 1 indicates external reference and 2 indicates check mode. --------------------…

100%1 / 5282
Used by: GSP5,GP2,GP3,GPX,NXTP
Cause: 印刷模式在范围之外。
Remedy: 请确认生产程序的Ｓｑｇ＿ａｃｔｉｏｎ。范围是0～2。 0:单程　1:往复　2:单程一定方向
可以设定的连续往复印刷设定为，0：单程印刷，１：往复印刷。（ＧＰＸ,NXTP）
------------------------------
Code: 1101E00C
Display: 与编码相同
Used by: GSP5,GPX,NXTP
Cause: 印刷压力（Ｌ１）在范围之外。
印刷压力（从前到后）超出范围。（ＧＰＸ,NXTP）
Remedy: 请确认生产程序的Ｐｒｉｎｔ＿ｐｒｅｓ＿ｓｑｇＬ。范围是１～１００[%]。
可以设定的印刷压力为１０～２００Ｎ。（ＧＰＸ）
------------------------------
Code: 1101E00D
Display: 与编码相同
Used by: GSP5,GPX,NXTP
Cause: 印刷压力（Ｒ１）在范围之外。 印刷压力（从后到前）超出范围。（ＧＰＸ,NXTP）
Remedy: 请确认生产程序的Ｐｒｉｎｔ＿ｐｒｅｓ＿ｓｑｇＲ。范围是１～１００[%]。 可以设定的印刷压力为
１０～２００Ｎ。（ＧＰＸ）
------------------------------
Code: 1101E00E
Display:
Used by: GSP5
Cause: The squeegee size is out of range.
Remedy: Check Squeegee_size in the production program. A setting of 0 indicates L, 1 indicates M and 2
indicates S.
------------------------------
Code: 1101E00F
Display: 1101E00F
Used by: GSP5,GP2,GP3,GP551,GP6
Cause: Side clamp pressure is out of range.
Remedy: Check Clamp_pressure in the production program. The range is from 0 to 10000 g. The range
for the GSP5 is from 0 to 5000 g.
------------------------------
Code: 1101E010
Display: 与编码相同
Used by: GSP5,GP2,GP3,GPX,NXTP
Cause: 真空模式在范围之外。
Remedy: 请确认生产程序的Ｖａｃｕｕｍ＿ｆｌａｇ。
范围是0～2。0:不使用　1:全部使用　2:印刷中ｏｆｆ
请确认在ＦｕｊｉＦｌｅｘａ上设定的电路板真空设定。范围为，０：电路板真空无，１：电路板真空有。（GPX）
------------------------------
Code: 1101E011
Display: 与编码相同
Used by: GSP5,GPX,NXTP
Cause: 非接触式印刷时的电路板与网板的距离在范围之外。
Remedy: 请确认生产程序的ｏｆｆｃｏｎｔａｃｔ＿ｄｉｓｔａｎｃｅ。范围是０.００～３.００[mm]。
请确认在ＦｕｊｉＦｌｅｘａ上设定的非接触量。范围为，从－１到１ｍｍ。（ＧＰＸ,NXTP）
------------------------------
Code: 1101E012
Display:
第 122 页
Used by: GSP5
Cause: Edge mode is out of range.
Remedy: Check Clamp_mode in the production program. A setting of 0 indicates mark reference, 1
indicates external reference and 2 indicates check mode.
------------------------------
Code: 1101E013
Display:
Used by: GSP5
Cause: When edge mode is check mode, the external reference is out of range.
Remedy: Check Edge_revise_limit in the production program. The range is from 0.01 to 1.00 mm.
------------------------------
Code: 1101E014
Display:
Used by: GSP5
Cause: The elongation limit is out of range.
Remedy: Check Elongation_limit in the production program. The range is from 0.00 to 10.00%.
------------------------------
Code: 1101E015
Display: 与编码相同
Used by: GSP5,GP2,GP3,GPX,NXTP
Cause: 绝对修正值X在范围之外。
Remedy: 请确认生产程序的Ａｂｓｏｌｕｔｅ＿ｏｆｓｔ．X。范围是-１.２８～１.２７[mm]。
请确认在ＦｕｊｉＦｌｅｘａ上设定的绝对偏移量X。范围为－１．２７～１．２８ｍｍ。（ＧＰＸ,NXTP）
------------------------------
Code: 1101E016
Display: 与编码相同
Used by: GSP5,GP2,GP3,GPX,NXTP
Cause: 绝对修正值Y在范围之外。
Remedy: 请确认生产程序的Ａｂｓｏｌｕｔｅ＿ｏｆｓｔ．Y。范围是-１２８～１.２７[mm]。
请确认在ＦｕｊｉＦｌｅｘａ上设定的绝对偏移量Ｙ。范围为－１．２７～１．２８ｍｍ。（ＧＰＸ,NXTP）
------------------------------
Code: 1101E017
Display:
Used by: GSP5
Cause: The center of compensation in the X-axis is out of range.
Remedy: Check Screen_locate_orgn_x in the production program. The range is -457.00 to 457.00 mm.
------------------------------
Code: 1101E018
Display:
Used by: GSP5
Cause: The center of compensation in the Y-axis is out of range.
Remedy: Check Screen_locate_orgn_y in the production program. The range is -356.00 to 356.00 mm.
------------------------------
Code: 1101E019
Display: 与编码相同
Used by: GSP5,GPX
Cause: The snapoff speed is out of range.
Remedy: Check Board_detach_speed in the production program. The range is from 0.1 to 1.0 mm/sec.
Check the detach speed for the first sequence in Fuji Flexa. Possible detach speed range: 0.1 to 40 mm/s
请确认在ＦｕｊｉＦｌｅｘａ上设定的第１顺序的离板速度。范围为，从０．１到４０[mm/sec]。（ＧＰＸ）
------------------------------
第 123 页
Code: 1101E01A
Display: 与编码相同
Used by: GPX,NXTP
Cause: 离板距离超出范围。
Remedy: 请确认生产程序的Ｂｏａｄ＿ｄｅｔａｃｈ＿ｄｉｓｔａｎｃｅ。
从０.０到５.０[mm](GSP3)
请确认Job编制器的Detach Mask - Height。
从０.０到４.０[mm](GPX)
从０.０到５.０[mm](NXTP)
------------------------------
Code: 1101E01B
Display:
Used by: GSP5,GP2,GP3
Cause: The specified number of knead times is out of range.
Remedy: Check Knead_times in the production program. The range is from 0 to 99.
------------------------------
Code: 1101E01C
Display:
Used by: GSP5,GP2,GP3
Cause: When in edge mode the compensation motor (MX) position is out of range.
Remedy: Check Screen_mx.orgn in the production program. The range is from -1000 to 30,000 pulses.
------------------------------
Code: 1101E01D
Display:
Used by: GSP5,GP2,GP3
Cause: When in edge mode the compensation motor (MYL) position is out of range.
Remedy: Check Screen_myl.orgn in the production program. The range is from -1000 to 30,000 pulses.
------------------------------
Code: 1101E01E
Display:
Used by: GSP5,GP2,GP3
Cause: When in edge mode the compensation motor (MYR) position is out of range.
Remedy: Check Screen_myr.orgn in the production program. The range is from -1000 to 30,000 pulses.
------------------------------
Code: 1101E01F
Display: 与编码相同
Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP
Cause: 钢板读取计数在范围之外。
Remedy: 请确认生产程序的Ｍａｓｋ＿ｒｅａｄ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认
Ｍａｓｋ＿ｒｅａｄ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块](如果是ＧＳＰ５时，范围是０～６００００[块
])。
------------------------------
Code: 1101E020
Display: 与编码相同
Used by: GSP5,GP2,GP3,GP551,GP6,GPX,NXTP
Cause: 清洁计数器在范围之外。
Remedy: 请确认生产程序的Ｃｌｅａｎｉｎｇ＿ｃｏｕｎｔｅｒ（在ＧＰ６中使用了Ｆ４Ｇ时，确认
Ｃｌｅａｎｉｎｇ＿ｉｎｔｅｒｖａｌ）。范围是０～６５０００[块](如果是ＧＳＰ５时，范围是０～６００００[块
])。 请确认在ＦｕｊｉＦｌｅｘａ上设定的自动清洁计数。范围为０～９９９９［块］。（GPX,NXTP）
------------------------------
Code: 1101E021
第 124 页