FUJI错误代码查询 - 第1251页

data. ------------------------------ Code: 1D01C6?? Display: Used by: Cause: An edge could not be detected on the right side of the part. Remedy: Check the part. Check the direction of part supply. Check the entries in P…

100%1 / 5282
Code: 1D01B7??
Display:
Used by:
Cause: There is no lead where there ought to be one on the upper side of the part. The final two digits
indicate the lead number.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C0??
Display:
Used by:
Cause: A lead could not be detected on the left side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C1??
Display:
Used by:
Cause: A lead could not be detected on the lower side of the part. The two final digits indicate the lead
number.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C2??
Display:
Used by:
Cause: A lead could not be detected on the right side of the part. The two final digits indicate the lead
number.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C3??
Display:
Used by:
Cause: A lead could not be detected on the upper side of the part. The two final digits indicate the lead
number.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C4??
Display:
Used by:
Cause: An edge could not be detected on the left side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C5??
Display:
Used by:
Cause: An edge could not be detected on the lower side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
第 1250 页
data.
------------------------------
Code: 1D01C6??
Display:
Used by:
Cause: An edge could not be detected on the right side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01C7??
Display:
Used by:
Cause: An edge could not be detected on the upper side of the part.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01D000
Display:
Used by:
Cause: The part pickup slippage was too large (X direction).
Remedy: Check how the parts are being supplied.
------------------------------
Code: 1D01D080
Display:
Used by:
Cause: The part pickup slippage was too large (Y direction).
Remedy: Check how the parts are being supplied.
------------------------------
Code: 1D01E???
Display:
Used by:
Cause: The image in vision processing is not correct so operation was canceled.
Remedy: Check the part. Check the direction of part supply. Check the entries in Part data and Device
data.
------------------------------
Code: 1D01F???
Display:
Used by:
Cause: There was a logical error in the management program.
Remedy: Check Part data.
------------------------------
Code: 1D020001
Display:
Used by:
Cause: All the necessary Part data has not been entered.
Remedy: Enter the necessary data.
------------------------------
Code: 1D020002
Display:
Used by:
Cause: The part cannot be picked.
第 1251 页
Remedy: Replenish the part supply.
------------------------------
Code: 1D020003
Display:
Used by:
Cause: An image cannot be taken by vision processing. The part is too large.
Remedy: Check the camera, vision processing board, cable and focus. Check the part. The lead has to
have a certain thickness to be detected. If the lead thickness is not within +-50% of the thickness set in
Part data this error can occur. Check the part lead and the CCD level.
------------------------------
Code: 1D020004
Display:
Used by:
Cause: The part lead cannot be found.
Remedy: Check that the lead exists, and check the thickness of the lead. Check the part. The lead has to
have a certain thickness to be detected. If the lead thickness is not within +-50% of the thickness set in
Part data this error can occur. Check the part lead and the CCD level.
------------------------------
Code: 1D020005
Display:
Used by:
Cause: The lead width is too wide.
Remedy: Check the thickness of the lead. Check the part. The lead has to have a certain thickness to be
detected. If the lead thickness is not within +-50% of the thickness set in Part data this error can occur.
Check the part lead and the CCD level.
------------------------------
Code: 1D020006
Display:
Used by:
Cause: No leads can be found.
Remedy: Check whether the lead exists, and check the orientation of the parts when they are fed to the
machine. The lead has to have a certain thickness to be detected. If the lead thickness is not within +-
50% of the thickness set in Part data this error can occur. Check the part lead and the CCD level.
------------------------------
Code: 1D020007
Display:
Used by:
Cause: The lead width is too wide.
Remedy: Check the thickness of the lead. Check the part. The lead has to have a certain thickness to be
detected. If the lead thickness is not within +-50% of the thickness set in Part data this error can occur.
Check the part lead and the CCD level.
------------------------------
Code: 1D020008
Display:
Used by:
Cause: The lead pitch is too wide.
Remedy: Check the lead pitch, and check the orientation of the parts when they are fed to the machine.
The lead has to have a certain thickness to be detected. If the lead thickness is not within +-50% of the
thickness set in Part data this error can occur. Check the part lead and the CCD level.
------------------------------
Code: 1D020009
第 1252 页