FUJI错误代码查询 - 第164页

Display: 11022715 Used by: Cause: During HELPS operation, the Reader_type in Proper data is set to a value other than 0 when the board type report for LMS is manual terminate. Remedy: Retransmit Proper data after setting…

100%1 / 5282
Used by: IP3
Cause: Conveyor Adj.Limit has no value specified even though the conveyor is being adjusted
automatically.
Remedy: Input an appropriate value in Proper data's 26.Conveyor Adj.Limit item.
------------------------------
Code: 1102270E
Display:
Used by: IP3
Cause: Conveyor Stop_offset has no value specified even though the conveyor is being adjusted
automatically.
Remedy: Input an appropriate value in Proper data's 27.Conveyor Stop_offset item.
------------------------------
Code: 1102270F
Display:
Used by: IP3
Cause: The value input in Conveyor Adj.Limit is smaller than the value input in Conveyor Stop_offset.
Remedy: Input a value in 26.Conveyor Adj.Limit which is larger than the value in 27.Conveyor
Stop_offset.
------------------------------
Code: 11022710
Display:
Used by: IP3
Cause: Conveyor adj. Timer has no value specified even though the conveyor is being adjusted
automatically.
Remedy: Input an appropriate value in Proper data's 28.Conveyor adj. Timer item.
------------------------------
Code: 11022711
Display:
Used by: IP3
Cause: Width Max Limit has no value specified.
Remedy: Input an appropriate value in Proper data's 29.Width Max Limit item.
------------------------------
Code: 11022712
Display:
Used by: IP3
Cause: Width Min Limit has no value specified.
Remedy: Input an appropriate value in Proper data's 30.Width Min Limit item.
------------------------------
Code: 11022713
Display:
Used by: IP3
Cause: The value input in Width Max Limit is smaller than the value input in Width Min Limit.
Remedy: Input a value in 29.Width Max Limit which is larger than the value in 30.Width Min Limit.
------------------------------
Code: 11022714
Display:
Used by: IP3,QP132
Cause: Terminal Type has no value specified.
Remedy: Input an appropriate value in Proper data's 56.Terminal Type item.
------------------------------
Code: 11022715
第 163 页
Display: 11022715
Used by:
Cause: During HELPS operation, the Reader_type in Proper data is set to a value other than 0 when the
board type report for LMS is manual terminate.
Remedy: Retransmit Proper data after setting Reader_type in Proper data to 0.
------------------------------
Code: 11022716
Display: Same as code
Used by: CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP642M,CP643,CP643M
Cause: A value other than "30" has been specified at Proper data item "change_over_mode", even though
Proper data item "reader_type is set to "4". Or, a value other than "4" has been specified at Proper data
item "reader_type", even though Proper data item "change_over_mode" is set to "30".
Remedy: Check Proper data items "reader_type" and "change_over_mode".
------------------------------
Code: 11022800
Display:
Used by:
Cause: When Proper data was checked, there was no Proper for the peripgerals.
Remedy: Transmit the Proper data for the peripherals.
------------------------------
Code: 11022801
Display:
Used by:
Cause: Machine_type is set incorrectly.
Remedy: After checking the Machine_type setting in MCS, re-transmit the Proper data to the machine.
1 = flip station.
2 = input terminal.
3 = output terminal.
4 = intermediate buffer.
5 = board stacker.
7 = MBID.
8 = ferris wheel feeder.
------------------------------
Code: 11022802
Display:
Used by:
Cause: Machine_control_port is set incorrectly.
Remedy: After checking the Machine_control_port setting, re-transmit the Proper to the machine. When
machine_control_mode is set at 2~5, a setting must be made for MBID. This setting connects the next
production stage and the RS-232C cable to the LCU connector (connector number 1~8).
Do not use the settings 1, 3 or those chosen for Command_line_port, Reader1_port, Reader2_port or
Code_terminal_port. Normally setting 7 is used. This is set when the machine is shipped.
------------------------------
Code: 11022803
Display:
Used by:
Cause: Machine_control_mode is set incorrectly.
Remedy: After checking Machine_control_mode in MCS, re-transmit the Proper data.
0 = outside MBID.
1 = working display.
2 = Research MP-4470 Reflow oven.
第 164 页
3 = Tamura VPS Reflow oven.
4 = Koki Reflow oven.
5 = Senju Reflow Oven.
Do not use
------------------------------
Code: 11022900
Display:
Used by: IP3
Cause: Origin_Position_X has no value specified.
Remedy: Input an appropriate value in Proper data's 100.Origin_Position_X item.
------------------------------
Code: 11022901
Display:
Used by: IP3
Cause: Origin Position Y has not been specified.
Remedy: Specify a value in Proper data item 100.Origin_Position_Y.
------------------------------
Code: 11022902
Display:
Used by: IP3
Cause: Nozzle position X1 has no data value specified.
Remedy: Input the offset pulse value from the mark camera center to nozzle 1 in the X direction. For the
FLT, input a value in 102.Nozzle_Position_X and for the IP3, input a value in 102.Nozzle1_Position_X.
------------------------------
Code: 11022903
Display:
Used by: IP3
Cause: Nozzle position X2 (offset pulse) has no data entered.
Remedy: Input the offset pulse value from the mark camera center to nozzle 2 in the X direction. For the
IP3, input a value in 103.Nozzle2_Position_X.
------------------------------
Code: 11022904
Display:
Used by: IP3
Cause: The vision processing camera 1 position has not been specified.
Remedy: Measure the pulse values from the center of the mark camera to the center of vision processing
camera 1. Input this value into 103.Camera1_Position_X for the FLT and 104.Camera1_Position_X for the
FIP3.
------------------------------
Code: 11022905
Display:
Used by: IP3
Cause: The vision processing camera 2 position has not been specified.
Remedy: Measure the pulse values from the center of the mark camera to the center of vision processing
camera 2. Input this value into 104.Camera2_Position_X for the FLT and 105.Camera2_Position_X for the
FIP3.
------------------------------
Code: 11022906
Display:
Used by:
Cause: The 1st pin check camera (#1) position has not been specified.
第 165 页