FUJI错误代码查询 - 第1854页
Remedy: Re-install the Host communication software. ------------------------------ Code: 210010F4 Display: Read error Used by: Cause: An error occurred while reading data from the disk. Remedy: Check that the file can be…
------------------------------
Code: 21001043
Display: Illegal argument
Used by:
Cause: The start-up parameters are incorrect.
Remedy: Correct the parameters (set the overwrite mode, change the file directory, etc.)
------------------------------
Code: 210010CF
Display: Process Memory full
Used by:
Cause: Sufficient memory area could not be allocated as the work area to carry out conversion of
transmitted data.
Remedy: Check that there is sufficient memory to operate the system. If there isn't, perform a system
reset.
------------------------------
Code: 210010D3
Display: End of file
Used by:
Cause: The end of file (EOF) character was detected while a file was being read.
Remedy: The file format is incorrect. The file has probably been damaged for some reason. Run the
communication function again with a different file. If the error occurs again with the new file.
------------------------------
Code: 210010D6
Display: File not accesible
Used by:
Cause: The file is write protected, so it is not possible to write data to the file or to delete the file.
Remedy: Use the File Services function from the UCI menu to cancel the write protection.
------------------------------
Code: 210010D7
Display: Bad path name
Used by:
Cause: The directory (path) is specified incorrectly.
Remedy: Specify the directory correctly.
------------------------------
Code: 210010D8
Display: File not found
Used by:
Cause: A non-existent file was specified.
Remedy: Check the file name.
------------------------------
Code: 210010DA
Display: File already exists
Used by:
Cause: A Part Data file with the same name already exists, and the current file cannot be loaded.
Remedy: Set the overwrite mode to YES to replace the contents of the existing file, or specify a new file
name.
------------------------------
Code: 210010DD
Display: Module not found
Used by:
Cause: The specified module does not exist, or could not be loaded.
第 1853 页
Remedy: Re-install the Host communication software.
------------------------------
Code: 210010F4
Display: Read error
Used by:
Cause: An error occurred while reading data from the disk.
Remedy: Check that the file can be read in the editor. If not, the file has been destroyed.
------------------------------
Code: 210010F5
Display: Write error
Used by:
Cause: An error occurred while writing data to the disk.
Remedy: Check the condition of the disk (available memory, partitions, etc.).
------------------------------
Code: 210010F6
Display: Device not ready
Used by:
Cause: The disk is not moving.
Remedy: Re-boot MCS.
------------------------------
Code: 210010F8
Display: Media full
Used by:
Cause: There is no space available on the disk.
Remedy: Delete unused files from the disk.
------------------------------
Code: 21001719
Display: Connection time over
Used by:
Cause: Reply or communication was not completed within the fixed time.
Remedy: Start again from the beginning. If there is still a problem, check the cable connections and MCS
settings.
------------------------------
Code: 21001751
Display: File descriptor not found
Used by:
Cause: The file descriptor required for data conversion does not exist.
Remedy: Re-install the Host communication software.
------------------------------
Code: 21001752
Display: File descriptor format error
Used by:
Cause: The contents of the file descriptor are not correct.
Remedy: Re-install the Host communication software.
------------------------------
Code: 21001761
Display: Character substitution file error
Used by:
Cause: The character substitution file is incorrect.
Remedy: Check the file.
------------------------------
第 1854 页
Code: 21001770
Display:
Used by:
Cause: The IDG could not boot up.
Remedy: Check that the optional GD editor disk has been installed.
------------------------------
Code: 21001771
Display: IDG process error
Used by:
Cause: IDG process error
Remedy: Refer to the GDG error and check Part data.
------------------------------
Code: 21001780
Display: PTN converter fork error
Used by:
Cause: It was not possible to start the PTN conversion program. Either the PTN change program is not
functioning correctly or it is not installed.
Remedy: Re-install the system.
------------------------------
Code: 21001781
Display: PTN converter process error
Used by:
Cause: During PTN conversion, an error occurred and execution stopped.
Remedy: Refer to error status. Check the error information which is output from the PTN conversion
program. After the error has been corrected, resume operation.
------------------------------
Code: 21001801
Display: Syntax error in download data
Used by:
Cause: The downloaded data contains some abnormal data.
Remedy: Correct the download program.
------------------------------
Code: 21001810
Display: Data size error
Used by:
Cause: The downloaded data contains too many lines.
Remedy: Correct the downloaded program.
------------------------------
Code: 21001811
Display: Data type error
Used by:
Cause: The downloaded data is the wrong type of data.
Remedy: Correct the download program.
------------------------------
Code: 21001812
Display: Data overflow
Used by:
Cause: A downloaded data value is too large to be saved.
Remedy: Correct the download program.
------------------------------
Code: 21001813
第 1855 页