FUJI错误代码查询 - 第2073页

Used by: Cause: An error occurred during execution of Dsave (control). Remedy: Re-execute the function. ------------------------------ Code: 2100E401 Display: dsave file open error Used by: Cause: The Dsave procedure fil…

100%1 / 5282
------------------------------
Code: 2100E150
Display:
Used by:
Cause: The backup disk is protected so that the backing up operation cannot proceed.
Remedy: Remove the write protect label from the backup disk and load the disk in the drive again.
------------------------------
Code: 2100E200
Display: Pr_pipe open error
Used by:
Cause: The print command pipe (pr_pipe) could not be opened.
Remedy: Re-boot MCS.
------------------------------
Code: 2100E300
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly.
------------------------------
Code: 2100E301
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly.
------------------------------
Code: 2100E310
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly.
------------------------------
Code: 2100E311
Display:
Used by:
Cause: The device was specified incorrectly.
Remedy: Check and specify the device correctly. Contact Fuji if the problem cannot be solved.
------------------------------
Code: 2100E350
Display: parameter error
Used by:
Cause: The parameters to boot up the time-setting routine are incorrect.
Remedy: Re-execute the function.
------------------------------
Code: 2100E351
Display: not found
Used by:
Cause: The rtclock2 module does not exist.
Remedy: Re-install the software.
------------------------------
Code: 2100E400
Display: dsave command error
第 2072 页
Used by:
Cause: An error occurred during execution of Dsave (control).
Remedy: Re-execute the function.
------------------------------
Code: 2100E401
Display: dsave file open error
Used by:
Cause: The Dsave procedure file could not be opened.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E403
Display: chdir() error
Used by:
Cause: The current directory could not be changed.
Remedy: Re-execute the function.
------------------------------
Code: 2100E404
Display: command error during **** process
Used by:
Cause: An error occurred during hard disk maintenance.
Remedy: Re-execute the function.
------------------------------
Code: 2100E406
Display: keyboard error
Used by:
Cause: An error occurred during key input.
Remedy: Re-execute the function.
------------------------------
Code: 2100E408
Display: get file size error
Used by:
Cause: The number of temporary media could not be calculated.
Remedy: Re-execute the function.
------------------------------
Code: 2100E411
Display: temporary device open error
Used by:
Cause: A temporary file could not be opened.
Remedy: Check that the floppy disk is set correctly in the drive.
------------------------------
Code: 2100E504
Display: change console path error
Used by:
Cause: The standard I/O path could not be selected to the terminal.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
------------------------------
Code: 2100E505
Display: CRT event link error
Used by:
Cause: A CRT event could not be linked.
Remedy: Re-execute the function. If the error recurs, re-boot MCS.
第 2073 页
------------------------------
Code: 2100E506
Display: active drive disk not found
Used by:
Cause: The active disk is not stored in the environment variables file.
Remedy: Set the active disk in the environment variables file.
------------------------------
Code: 2100E507
Display: printer stop error
Used by:
Cause: The printer output could not be stopped. (Ctrl + X)
Remedy: Re-boot MCS.
------------------------------
Code: 2100E508
Display: RS-232C event link error
Used by:
Cause: An RS-232C event could not be linked.
Remedy: Re-boot MCS.
------------------------------
Code: 2100E509
Display: RS-232C event post error
Used by:
Cause: An RS-232C event could not be posted.
Remedy: Re-boot MCS.
------------------------------
Code: 2100E50A
Display: Line descriptor load error
Used by:
Cause: The Line Descriptor could not be loaded.
Remedy: Check the line descriptor.
------------------------------
Code: 2100E50B
Display: pipe cannot occupy
Used by:
Cause: The named pipe for the production monitor could not be occupied.
Remedy: Re-execute the function after waiting a while.
------------------------------
Code: 2100E50C
Display: Print file create error
Used by:
Cause: The print output file could not be created.
Remedy: Re-boot MCS.
------------------------------
Code: 2100E50D
Display: Printer output error
Used by:
Cause: Printer output is not possible.
Remedy: Check the printer cable connector, and check that the machine is in on-line mode.
------------------------------
Code: 2100E50E
Display: system monitor start error
第 2074 页