FUJI错误代码查询 - 第2178页

Code: 230A2005 Display: Cannot image-edit. Used by: PDW Cause: An error occurred when starting lEditor.exe. Remedy: Confirm that the lEditor.exe file exists. ------------------------------ Code: 230A3100 Display: 找不到文件 U…

100%1 / 5282
Remedy: Stop importing images and perform composition.
------------------------------
Code: 230A0010
Display: No images for composition.
Used by: PDW
Cause: An error occurred during composition.
Remedy: Import images that can be composed.
------------------------------
Code: 230A0011
Display: Multiframe acquisitions cannot be carried out on fields of view where X = 50 mm or less.
Used by: PDW
Cause: The field of view is too narrow.
Remedy: Change the field of view and perform calibration.
------------------------------
Code: 230A0012
Display: No part data file.\nClosing PDW.
Used by: PDW
Cause: PDW cannot be started because the specified PDS file does not exist.
Remedy: Correct the PDS file specification and retry.
------------------------------
Code: 230A0013
Display: Part Data Wizard V1.10 cannot be used with Vision Type %d.\nClosing PDW.
Used by: PDW
Cause: PDW cannot be started because the specified vision type is not supported.
Remedy: Change the PTPVICVT value in the PDS file.
------------------------------
Code: 230A2001
Display: Calibration error
Used by: PDW
Cause: The calibration plate was not recognized correctly.
Remedy: Check that the calibration plate image has been acquired correctly.
------------------------------
Code: 230A2002
Display: Field of view out of range.
Used by: PDW
Cause: The field of view has exceeded the target area for image recognition.
Remedy: Reduce the field of view and carry out calibration again.
------------------------------
Code: 230A2003
Display: Cannot edit.
Used by: PDW
Cause: Failed to enlarge the image because the unit value is invalid.
Remedy: Carry out calibration again.
------------------------------
Code: 230A2004
Display: Adjustment failed.
Used by: PDW
Cause: Failed to set the shutter speed necessary for the specified brightness.
Remedy: Check that there is an image displayed with the brightness adjusted within the correct range,
then carry out the adjustment again.
------------------------------
第 2177 页
Code: 230A2005
Display: Cannot image-edit.
Used by: PDW
Cause: An error occurred when starting lEditor.exe.
Remedy: Confirm that the lEditor.exe file exists.
------------------------------
Code: 230A3100
Display: 找不到文件
Used by: PDW,GPX,NXTP
Cause: 在设定查找线时，所需的文件有可能破坏了而没有找到。
Remedy: 请重新安装PDW。 请重新编辑和修正定位点形状。（GPX,NXTP)
------------------------------
Code: 230A3101
Display: Maximum input level reached.
Used by: PDW
Cause: You attempted to set over ten points in the shape data during shape editing.
Remedy: Delete the existing shape data and set new shape data.
------------------------------
Code: 230A3102
Display: Maximum input level reached.
Used by: PDW
Cause: You attempted to set over 30 points on the fold line.
Remedy: Set 30 or fewer points on the fold lines.
------------------------------
Code: 230A3103
Display: Pitch measurement error.
Used by: PDW
Cause: Failed to measure the pitch when the template file was compiled.
Remedy: Reset the seek lines.
------------------------------
Code: 230A3104
Display: Edge position compensation cannot be performed because either there are no\nseek lines or none
of the seek lines has an edge.
Used by: PDW
Cause: The brightness deviation cannot be calculated because none of the seek lines have any edge flags
set.
Remedy: Set edge detection for at least one of the seek lines.
------------------------------
Code: 230A3105
Display: Cannot re-edit.
Used by: PDW
Cause: Either the template file is corrupt, or the image file cannot be found.
Remedy: Create the template again.
------------------------------
Code: 230A3106
Display: A Find seek line is necessary.
Used by: PDW
Cause: A Find must be specified for the template to be created, but none have been set.
Remedy: Compensate the position of the edges, or set a Find for some of the seek lines.
------------------------------
Code: 230A3107
第 2178 页
Display: There is Position seek line whose edge position compensation is incomplete.
Used by: PDW
Cause: The edge positions have not been compensated after setting the Position seek lines.
Remedy: Compensate the position of the edges.
------------------------------
Code: 230A3108
Display: There is an Inspection seek line whose edge position compensation is incomplete.
Used by: PDW
Cause: The edge positions have not been compensated after setting the Inspection seek lines.
Remedy: Compensate the position of the edges.
------------------------------
Code: 230A3109
Display: Recognition error.
Used by: PDW
Cause: Inspection failed.
Remedy: Carry out the seek line settings again.
------------------------------
Code: 230A310A
Display: Edge position compensation was not successful for some seek lines.
Used by: PDW
Cause: No edges were found above the seek lines for finding edges.
Remedy: Move the edge finding seek lines to positions where they cross over edges.
------------------------------
Code: 230A3201
Display: Recognition error.
Used by: PDW
Cause: An error occurred during image recognition.
Remedy: Input element data that can be recognized.
------------------------------
Code: 230A3202
Display: Maximum input level reached.
Used by: PDW
Cause: More than 128 lead elements have been input.
Remedy: Delete the current element data and specify new element data.
------------------------------
Code: 230A3203
Display: Size could not be determined.
Used by: PDW
Cause: The average width of the leads being edited is 0.
Remedy: Input element data that can be recognized.
------------------------------
Code: 230A3204
Display: No element data.
Used by: PDW
Cause: No elements have been input.
Remedy: Input element data.
------------------------------
Code: 230A3205
Display: Requires 1 or more elements with 5 or more leads.
Used by: PDW
Cause: There are no elements with 5 or more leads.
第 2179 页