FUJI错误代码查询 - 第288页
请清除生产完成块数。(NP2,QP3) ------------------------------ Code: 12010402 Display: 无 Used by: GSP2,GSP3,GPX,NXTP Cause: 维修保养计数器到了设定值。 通用计数器递增计数了。 (GPX) Remedy: 请擦拭网板的反面等维修保养作业，然后重新进入自动运转。(GSP2) 请通过[设定]ー[状态]ー[计数器]进行清 除 (GP6 GP5) …
Remedy: Ensure that the paired device number is within the range of 000 - 255.
------------------------------
Code: 11E006??
Display: None
Used by: CP43,FCP6,CP6M,CP642,CP642M
Cause: During use of the pair parts function, the value specified at the part data item "Empty_cavities" is
outside the acceptable range (CP-6-series), or the specified recovery setting is outside the acceptable range
(CP-43). The question marks (??) represent the device number in hexadecimal format.
Remedy: Set the number of empty cavities within the range of 2 to 10, and set the number of recovery
attempts within the range of 0 to 4.
------------------------------
Code: 12010101
Display: 紧急停止开关 NG EMERGENCY(CP3)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GSP5,GP2,GP3,GP551,GP6,IP
1,IP3,QP242,QP201,QP202,QP203,QP132,NP132,NP133,CP-732E,CP-742ME,CP-742E,CP-
752E,GPX,NXTP
Cause: 紧急停止开关被按下了。
Remedy: 请复位紧急停止开关。紧急停止开关带有锁定功能。朝箭头方向（顺时针方向）转动后，锁定就会被解除。
·请按下电源关闭按钮，关闭电源。(CP3)
·请按下电源关闭按钮关闭电源(结束生产时)或者按下复位按钮。(GL)
<img src="$LKEY_ERRIMG_MC$/12010101.PNG">
------------------------------
Code: 12010201
Display: “ 周期停止 ”
Used by: GSP2,GSP3,GSP5,GP2,GP3,IP1,GPX
Cause: 周期停止开关被按下了。
Remedy: 请按下复位按钮。
------------------------------
Code: 12010202
Display: 来自外部输入的停止信号ON
Used by: GPX,NXTP
Cause: 由于来自外部输入的停止信号ON着，因此停止了机器
Remedy: 请确认外部工程是否因错误而停止了。
<img src="$LKEY_ERRIMG_MC$/12010202.PNG">
------------------------------
Code: 12010301
Display:
Used by: CP4-1,CP4-2,CP4-3,CP5,CP6,CP6M,CP65,CP652C,CP642,CP643,GL541,IP1
Cause: The matching production program is finished.
Remedy: None.
------------------------------
Code: 12010401
Display: 完成了生产预定块数(CP5) PRODUCTION COMPLETE(CP3)
完成生产预定块数(GL,GSP2,IP2)
完成生产预定块数。(NP2,QP3)
Used by: CP3,CP4-1,CP4-2,CP4-
3,CP6,CP6M,CP65,CP652C,CP642,CP643,GL2,GL5,GL541,GSP2,GSP3,GP2,GP3,GP551,GP6,IP1,NP2,QP3,
GPX
Cause: 完成了生产预定块数。
Remedy: 请在PROGRAM - QTYCLR 中清除生产块数。(CP3,GL)
第 287 页
请清除生产完成块数。(NP2,QP3)
------------------------------
Code: 12010402
Display: 无
Used by: GSP2,GSP3,GPX,NXTP
Cause: 维修保养计数器到了设定值。 通用计数器递增计数了。 (GPX)
Remedy: 请擦拭网板的反面等维修保养作业，然后重新进入自动运转。(GSP2) 请通过[设定]ー[状态]ー[计数器]进行清
除 (GP6 GP5) 请进行刮刀更换或钢板的更换等必要的对应，将通用计数器清零。（GPX)
<img src="$LKEY_ERRIMG_MC$/12010402.PNG">
------------------------------
Code: 12010403
Display:
Used by: CP3,GL5
Cause: Seq End Stop. Automatic operation is finished.
Remedy: Press the start button and go back into automatic operation.
------------------------------
Code: 12010404
Display: Eject Tray
Used by: IP2
Cause: In a non-matrix tray, parts have run out and the machine stops.
Remedy: Discard the tray.
------------------------------
Code: 12010405
Display: 清洁计数结束
Used by: GPX
Cause: 清洁计数到了设定值。
Remedy: 通过[设定]ー[状态]ー[计数器]进行清除
------------------------------
Code: 12010406
Display: 焊锡供应计数结束
刮刀内焊锡余量不足
Used by: GP551,GPX
Cause: 焊锡供应计数到了设定值。或者，根据余量检测判断出焊锡余量不足。
Remedy: 请进行焊锡供应。请通过[设定]ー[状态]ー[计数器]进行清除。
------------------------------
Code: 12010407
Display: 手动清洁计数结束
Used by: GP551,GPX
Cause: 手动清洁计数到了设定值。
Remedy: 请通过[设定]ー[状态]ー[计数器]进行清除。
------------------------------
Code: 12010408
Display: "Pressure measurement counter limit"
Used by: GP551
Cause: The pressure measurement counter has reached its limit.
Remedy: Enter [SET], [STATUS] , then [COUNTER] to cancel this error.
------------------------------
Code: 12010501
Display: CLEAR OFF COMPLETE
Clear Off Has Been Finished
Clear Off Complete
第 288 页
Used by: CP3,CP4-1,CP4-2,CP4-3,CP6,CP6M,CP65,CP652C,CP642,CP643,GSP2,GP2,GP3
Cause: Clear off is finished.
Remedy: None.
------------------------------
Code: 12010701
Display: 往复臂运转模式错误
Used by: NXTP
Cause: 往复臂不是运转模式
Remedy: 请将往复臂置于运转模式
------------------------------
Code: 12010702
Display:
Used by:
Cause:
Remedy:
------------------------------
Code: 12020101
Display: PCM PLC Alarm
Used by: CP5
Cause: The pallet loader control system is down.
Remedy: Contact Fuji.
------------------------------
Code: 12020102
Display: Pallet ID Read Error (FCP5)
Pallet ID could not be Read (FCP651C)
Used by: CP652C
Cause: The ID could not be read. The acquisition of the ID for the pallet on the up-elevator has failed
(FCP651C).
Remedy: Verify that there is nothing abnormal about the pallet at the stand by station. Check that the ID
read position is not misaligned (FCP651C). Replace the ID card if read errors occur frequently. If the
pallet ID card is replaced, be sure that the ID_No. is written (recorded). Refer to the Operation Manual
concerning the ID_No. write Command.
------------------------------
Code: 12020103
Display: Check PPS Error
Used by: CP5
Cause: An error occurred at the PPS.
Remedy: Check the display and remove the cause of the error.
------------------------------
Code: 12020104
Display: PPS AUTO Mode Error
Used by: CP5
Cause: A pallet movement request was sent to the PPS when PPS was not in automatic mode.
Remedy: Start the PPS automatic mode.
------------------------------
Code: 12020105
Display: Plt Clear off to PPS Error
Used by: CP5
Cause: A request was made from PCM to PPS to unload pallets. The lower conveyor of the PPS was not
empty.
Remedy: Remove the pallet from the PPS lower conveyor.
第 289 页