FUJI错误代码查询 - 第492页

the table.Move the table to the loading position and ensure that the upper and lower sensors work properly by performing the lifter up/down command and performing an I/O check. ------------------------------ Code: 120501…

Display: "Pallet clamp error: IN stn"

Used by: CP5

Cause: The carrier pallet check sensor has not turned on even though the machine's pallet status

memory data indicates that there is a pallet in the IN station.

Remedy: If there is a pallet in the IN station, check the carrier pallet check sensor. If there is no pallet,

enter a command to set the IN station ID to 0.

------------------------------

Code: 12050105

Display: "Pallet clamp error: WRK stn"

Used by: CP5

Cause: The carrier pallet check sensor has not turned on even though the machine's pallet status

memory data indicates that there is a pallet in the WRK station.

Remedy: If there is a pallet in the WRK station, check the carrier pallet check sensor. If there is no pallet,

enter a command to set the WRK station ID to 0.

------------------------------

Code: 12050106

Display: "Pallet clamp error: OUT stn"

Used by: CP5

Cause: The carrier pallet check sensor has not turned on even though the machine's pallet status

memory data indicates that there is a pallet in the OUT station.

Remedy: If there is a pallet in the OUT station, check the carrier pallet check sensor. If there is no pallet,

enter a command to set the OUT station ID to 0.

------------------------------

Code: 12050107

Display: "Pallet clamp error: IN stn"

Used by: CP5

Cause: The IN station pallet check sensor has not turned on even though the machine's pallet status

memory data indicates that there is a pallet in the IN station.

Remedy: Check the IN station pallet check sensor.

------------------------------

Code: 12050108

Display: "Pallet clamp error: OUT stn"

Used by: CP5

Cause: The OUT station pallet check sensor has not turned on even though the machine's pallet status

memory data indicates that there is a pallet in the OUT station.

Remedy: Check the OUT station pallet check sensor.

------------------------------

Code: 12050109

Display: "1st pickup check sensor alarm"

Used by: CP5

Cause: The 1st robot component check sensor is stuck off.

Remedy: The 1st robot component check sensor is a reflection sensor. The will not turn on because the

sensor beam is improperly aligned.Adjust the sensor.

------------------------------

Code: 1205010A

Display: Lifter Not at lower limit (CP6/6M).

Used by: CP6

Cause: Before the XY table was moved in the automatic operation mode, the input from the table's lower

position 2 sensor (X032: TABLE DNCHK2) was checked, and found to be OFF. Therefore, to avoid a

collision, an emergency stop was made.

Remedy: Ensure that the sensor at table lower position 2 is working properly. Check for foreign objects on

第 491 页

the table.Move the table to the loading position and ensure that the upper and lower sensors work

properly by performing the lifter up/down command and performing an I/O check.

------------------------------

Code: 1205010B

Display: "Interlock: camera" (GP-6)

Used by: GP551,GP6

Cause: The Z-axis and X-axis are in the interference zone, or are interfering with each other. This error

may also be caused by a sensor error.

Remedy: If the Z-axis and Y-axis are interfering with each other, manually move the X-axis until the X-

axis escape position check sensor (X03D: X ESC POS CHK) is tripped. If they are in the interference zone,

or if there is no interference, check the X-axis escape position check sensor (X03D: X ESC POS CHK) and

the Z-axis camera interference prevention check sensor (X03C: Z ESC POS CHK).

------------------------------

Code: 1205010C

Display: Interlock Sqg/Cleaner Head

Used by:

Cause: This error occurs when both the upper cleaning head and the squeegee are in the lowered

position.

Remedy: Raise the cleaning head or the squeegee holder. Alternatively, check the following sensors:

(X070: (F) SQG HLDR UP, X078: R SQG HLDR UP) or (X07C: TP CLR OPN CHK, X05A: LW CLR OPN CHK).

------------------------------

Code: 1205010E

Display: Sqg Head Unlock

Used by: GP551,GP6

Cause: The squeegee head has been opened.

Remedy: Close and lock the squeegee head.

------------------------------

Code: 1205010F

Display: "Parking Position Error"

Used by: GP551,GP6

Cause: When a parking command is executed, the squeegee head is down after the S-axis has moved to

the position specified in the Proper data and the squeegee parking position check sensor (X03F) has

turned on. This error occurs when the squeegee parking position check sensor remains off after the S-axis

has moved.

Remedy: Check the position detected by the parking position check sensor and the position specified by

the "Parking Position S" parameter in the Proper data.These should be adjusted so that the sensor turns

on when the S-axis arrives at the parking position, and the squeegee head comes to rest on the screen

support when it is down.

------------------------------

Code: 12050110

Display: Sqg Head Position Error

Used by: GP551

Cause: The squeegee head is not in the locked position.

Remedy: Ensure that the squeegee head is in the locked position.

------------------------------

Code: 12050111

Display: Top Cleaner Position Error

Used by: GP551

Cause: The top cleaner swing bar is not in the locked position.

Remedy: Move the top cleaner swing bar to the locked position.

------------------------------

第 492 页

Code: 12050112

Display: Btm Cleaner Position Error

Used by: GP551

Cause: The lower cleaner tray is not in the locked position.

Remedy: Move the lower cleaner tray to the locked position.

------------------------------

Code: 12050113

Display: 印刷位置无网板

[Conf scr at print pos now]

Used by: GPX,NXTP

Cause: 印刷位置上没有网板。

Remedy: 请在印刷位置上设置网板。

------------------------------

Code: 12050114

Display: Warning! Top Cleaner may damage solder roll

Used by: GP551

Cause: On machines with double squeegees, solder may be present on the screen. During automatic

operation, cleaning of both sides cannot be performed.

Remedy: In Proper data, set the cleaning method to not use the upper cleaning unit.

------------------------------

Code: 12050115

Display: Placing head 1 nozzle has become detached.

Used by: IP3

Cause: The nozzle at placing head 1 has become detached.

Remedy: Remove the detached nozzle from within the machine. Either reattach the nozzle to the head by

hand, or set the nozzle in the nozzle change unit and use the [NOZZLE] -[CHANGE] commands to perform

reattachment.

------------------------------

Code: 12050116

Display: Placing head 2 nozzle has become detached.

Used by: IP3

Cause: The nozzle at placing head 2 has become detached.

Remedy: Remove the detached nozzle from within the machine. Either reattach the nozzle to the head by

hand, or set the nozzle in the nozzle change unit and use the [NOZZLE] -[CHANGE] commands to perform

reattachment.

------------------------------

Code: 12050117

Display: 传感器检测出挡块不可下降错误

Used by: NXTP

Cause: 因为传感器检测出电路板，所以不能降低挡块。

Remedy: 1.请清除电路板。

2.请调整传感器。

------------------------------

Code: 1205012?

Display: Nozzle damage has been detected on head 1.

Used by: NP133,NP134,NP153

Cause: The nozzle bend check sensor at head 1, 13ST has detected a nozzle error. The question mark (?)

indicates the nozzle position. If (?) is 0 then the error is on shaft A, if 1 then shaft B, if F then shaft P, etc.

Remedy: Replace the nozzle, either manually or using the nozzle change command.

第 493 页