FUJI错误代码查询 - 第614页

Remedy: Check that the parts are correct. ------------------------------ Code: 1206300D Display: Check Name Length Used by: Cause: The screen name is too long. Remedy: Screen name must not exceed 20 characters. Check the…

Remedy: Set a screen in the frame. Check the sensor.

------------------------------

Code: 12063007

Display: NOT SCREEN IN SUPPLY STOCKER

Used by: GSP2,GSP3

Cause: When the machine attempted to remove a screen from the upper stocker, a screen was not there.

Either the screen position shifted, or there was no screen and the sensor input was on (the upper stocker

light beam is interrupted).

Remedy: Confirm that a screen has been set into the stocker. Check the sensor.

------------------------------

Code: 12063008

Display: EXIT SCREEN IN TAKE_OUT STOCKER

Used by: GSP2,GSP3

Cause: A screen was already in the lower stocker when the machine attempted to store a screen. The

screen sensor for the lower stocker is off.

Remedy: Remove the screen from the lower stocker. Check the screen sensor.

------------------------------

Code: 12063009

Display: SCREEN POSITION IS BAD!

Used by: GSP2,GSP3

Cause: When the machine attempted to move the XY robot, at least one of the following conditions arose:

the frame set sensor is on, the frame push sensor is on, the frame supply normal sensor is shaded, the

frame X axis sensor is lighted, the right frame Y axis sensor is lighted, the left frame Y axis sensor is

lighted, the screen exchange in progress sensor is on.

Remedy: Check the position of the screen frame. Check each sensor.

------------------------------

Code: 1206300A

Display: SCREEN CHANGE ERROR

Used by: GSP2,GSP3

Cause: An error occurred during screen change.

Remedy: Refer to the display in the 2nd display area and perform that countermeasure.

------------------------------

Code: 1206300B

Display: 网板补正量在范围之外 (GSP)

Used by: GSP2,GSP3,GPX,NXTP

Cause: 想要进行网板补正，但是脉冲马达的移动量超出了Travel limit 的范围。补正马达目的地超过了移动范围

(GPX)

Remedy: 请检查程序的定位点坐标。请调整网板框的垫圈。请确认proper的travel_limit_mx ml mr 是否没有为０。

(参考)脉冲马达在零设定完成时的计数器为500。因为网板的补正范围是±５㎜，所以计数器值的０～1000为有效范围

。在ＧＳＰ－Ⅱ5000 中，脉冲马达的零设定完成时的计数器为1000，另外，因为网板的补正范围是±10㎜，所以计

数器值的０～2000为有效范围。请确认这些数值和proper的travel_limit_min travel_limit_max 的各MX,ML,MR的

设定。 1.请确认钢板的位置是否正确。

2.请确认电路板的尺寸是否正确。

3.不是在自动运转时，请确认补正马达的固有值MAX，MIN值是否正确。

4.存在可能需要重新测定补正马达原点的情况。（GPX)

------------------------------

Code: 1206300C

Display: DATA ERROR

Used by:

Cause: There was a data check error on the Handy Terminal.

第 613 页

Remedy: Check that the parts are correct.

------------------------------

Code: 1206300D

Display: Check Name Length

Used by:

Cause: The screen name is too long.

Remedy: Screen name must not exceed 20 characters. Check the screen name heading in the production

program.

------------------------------

Code: 1206300E

Display: cleaner not at origin

Used by: GSP5,GP551,GP6

Cause: The cleaner position is unknown.

Remedy: Return the cleaner to the origin position.

------------------------------

Code: 1206300F

Display: not enough solvent

Used by: GSP5

Cause: There is no cleaning fluid.

Remedy: Add cleaning fluid.

------------------------------

Code: 12063010

Display:

Used by: GP551,GP6

Cause: Ultrasonic oscillator alarm at the cleaner.

Remedy: Check that the power is on. If this error occurs frequently replace the oscillator.

------------------------------

Code: 12063011

Display:

Used by: GSP5

Cause: The solder supply/stop command was issued, but operation was not confirmed.

Remedy: The solder supply machine communication line is probably cut. Check the line.

------------------------------

Code: 12063012

Display:

Used by: GSP5

Cause: Operation could not be carried out because the solder supply machine was incorrectly positioned.

Remedy: After returning the solder supply machine to its origin position, restart operation.

------------------------------

Code: 12063013

Display: "Screen at rear cleaning position"

Used by:

Cause: The storage command cannot be executed because there is a screen at the rear cleaning position.

Remedy: Re-execute the storage command after removing the screen from the rear cleaning position.

------------------------------

Code: 12063014

Display:

Used by:

Cause: There is no screen in the backside cleaning position so the supply command cannot be executed.

Remedy: Set a screen in the backside cleaning position and execute the command.

------------------------------

第 614 页

Code: 12063015

Display: "Screen Error Print Pos"

Used by: GP551,GP6

Cause: Stencil transport was not possible because the stencil at the print position is not set correctly.

(GSP5) The stencil at the print position is not correctly set. (GP6)

Remedy: Move the stencil that was in the process of being transported, to the proper position. (GSP5)

Set the stencil that is at the print position, in the appropriate position to allow the stencilto be clamped.

This error will occur if the stencil cannot be properly clamped at this time. (GP6)

------------------------------

Code: 12063016

Display:

Used by:

Cause: The screen is not set properly in the backside cleaning position so it cannot be transported.

Remedy: Move the screen to where it can be properly transported.

------------------------------

Code: 12063017

Display: "No Stencil At Print Pos"

Used by: GP6

Cause: Automatic operation could not be started because there was no stencil at the print position. Or a

stencil could not be stored in the stocker.

Remedy: Set a stencil.

------------------------------

Code: 12063018

Display:

Used by:

Cause: The mask receiving unit is ascended.

Remedy: Lower the mask receiving unit.

------------------------------

Code: 12063019

Display:

Used by: GSP5

Cause: Even though the camera station is out, the S-axis wants to move out.

Remedy: Retract the camera station.

------------------------------

Code: 1206301A

Display:

Used by: GSP5

Cause: When the camera station is moving, it interferes with the Y-axis. Alternately, the Y-axis interlock

sensor is not working correctly.

Remedy: Retract the Y-axis so that it does not interfere with the camera station. Also, check the interlock

sensor.

------------------------------

Code: 1206301B

Display:

Used by: GSP5

Cause: When the camera station is moving, it interferes with the S-axis. Alternately, the S-axis interlock

sensor is not working correctly.

Remedy: Retract the S-axis so that it does not interfere with the camera station. Also, check the interlock

sensor.

------------------------------

Code: 1206301C

第 615 页